sentinel.conf配置

1.常用的配置

port 26379
# sentinel announce-ip <ip>
# sentinel announce-port <port>
dir "/tmp"

################################# master001 #################################
sentinel monitor master001 192.168.110.103 6379 2
# sentinel auth-pass <master-name> <password>
sentinel config-epoch master001 1
sentinel leader-epoch master001 1
sentinel known-slave master001 192.168.110.101 6379
# sentinel notification-script <master-name> <script-path>
# sentinel client-reconfig-script <master-name> <script-path>

# 可以配置多个master节点
################################# master002 #################################

配置文件说明：

1. port :当前Sentinel服务运行的端口

2. dir : Sentinel服务运行时使用的临时文件夹

3.sentinel monitor master001 192.168.110.101 6379 2:Sentinel去监视一个名为master001的主redis实例，这个主实例的IP地址为本机地址192.168.110.101，端口号为6379，而将这个主实例判断为失效至少需要2个 Sentinel进程的同意，只要同意Sentinel的数量不达标，自动failover就不会执行

4.sentinel down-after-milliseconds master001 30000:指定了Sentinel认为Redis实例已经失效所需的毫秒数。当实例超过该时间没有返回PING，或者直接返回错误，那么Sentinel将这个实例标记为主观下线。只有一个 Sentinel进程将实例标记为主观下线并不一定会引起实例的自动故障迁移：只有在足够数量的Sentinel都将一个实例标记为主观下线之后，实例才会被标记为客观下线，这时自动故障迁移才会执行

5.sentinel parallel-syncs master001 1：指定了在执行故障转移时，最多可以有多少个从Redis实例在同步新的主实例，在从Redis实例较多的情况下这个数字越小，同步的时间越长，完成故障转移所需的时间就越长

6.sentinel failover-timeout master001 180000：如果在该时间（ms）内未能完成failover操作，则认为该failover失败

7.sentinel notification-script <master-name> <script-path>：指定sentinel检测到该监控的redis实例指向的实例异常时，调用的报警脚本。该配置项可选，但是很常用

2.官方完整的配置

# Example sentinel.conf

# port <sentinel-port>
# The port that this sentinel instance will run on
# sentinel实例运行的端口
port 26379

# sentinel announce-ip <ip>
# sentinel announce-port <port>
#
# The above two configuration directives are useful in environments where,
# because of NAT, Sentinel is reachable from outside via a non-local address.
#
# When announce-ip is provided, the Sentinel will claim the specified IP address
# in HELLO messages used to gossip its presence, instead of auto-detecting the
# local address as it usually does.
#
# Similarly when announce-port is provided and is valid and non-zero, Sentinel
# will announce the specified TCP port.
#
# The two options don‘t need to be used together, if only announce-ip is
# provided, the Sentinel will announce the specified IP and the server port
# as specified by the "port" option. If only announce-port is provided, the
# Sentinel will announce the auto-detected local IP and the specified port.
#
# Example:
#
# sentinel announce-ip 1.2.3.4

# dir <working-directory>
# Every long running process should have a well-defined working directory.
# For Redis Sentinel to chdir to /tmp at startup is the simplest thing
# for the process to don‘t interferer with administrative tasks such as
# unmounting filesystems.
dir /tmp

# sentinel monitor <master-name> <ip> <redis-port> <quorum>
# master-name : master Redis Server名称
# ip : master Redis Server的IP地址
# redis-port : master Redis Server的端口号
# quorum : 主实例判断为失效至少需要 quorum 个 Sentinel 进程的同意，只要同意 Sentinel 的数量不达标，自动failover就不会执行
#
# Tells Sentinel to monitor this master, and to consider it in O_DOWN
# (Objectively Down) state only if at least <quorum> sentinels agree.
#
# Note that whatever is the ODOWN quorum, a Sentinel will require to
# be elected by the majority of the known Sentinels in order to
# start a failover, so no failover can be performed in minority.
#
# Slaves are auto-discovered, so you don‘t need to specify slaves in
# any way. Sentinel itself will rewrite this configuration file adding
# the slaves using additional configuration options.
# Also note that the configuration file is rewritten when a
# slave is promoted to master.
#
# Note: master name should not include special characters or spaces.
# The valid charset is A-z 0-9 and the three characters ".-_".
# 
sentinel monitor mymaster 127.0.0.1 6379 2

# sentinel auth-pass <master-name> <password>
#
# Set the password to use to authenticate with the master and slaves.
# Useful if there is a password set in the Redis instances to monitor.
#
# Note that the master password is also used for slaves, so it is not
# possible to set a different password in masters and slaves instances
# if you want to be able to monitor these instances with Sentinel.
#
# However you can have Redis instances without the authentication enabled
# mixed with Redis instances requiring the authentication (as long as the
# password set is the same for all the instances requiring the password) as
# the AUTH command will have no effect in Redis instances with authentication
# switched off.
#
# Example:
#
# sentinel auth-pass mymaster MySUPER--secret-0123passw0rd

# sentinel down-after-milliseconds <master-name> <milliseconds>
#
# Number of milliseconds the master (or any attached slave or sentinel) should
# be unreachable (as in, not acceptable reply to PING, continuously, for the
# specified period) in order to consider it in S_DOWN state (Subjectively
# Down).
# 选项指定了 Sentinel 认为Redis实例已经失效所需的毫秒数。当实例超过该时间没有返回PING，或者直接返回错误， 那么 Sentinel 将这个实例标记为主观下线（subjectively down，简称 SDOWN ）
#
# Default is 30 seconds.
sentinel down-after-milliseconds mymaster 30000

# sentinel parallel-syncs <master-name> <numslaves>
#
# How many slaves we can reconfigure to point to the new slave simultaneously
# during the failover. Use a low number if you use the slaves to serve query
# to avoid that all the slaves will be unreachable at about the same
# time while performing the synchronization with the master.
# 选项指定了在执行故障转移时， 最多可以有多少个从Redis实例在同步新的主实例， 在从Redis实例较多的情况下这个数字越小，同步的时间越长，完成故障转移所需的时间就越长。
sentinel parallel-syncs mymaster 1

# sentinel failover-timeout <master-name> <milliseconds>
#
# Specifies the failover timeout in milliseconds. It is used in many ways:
#
# - The time needed to re-start a failover after a previous failover was
#   already tried against the same master by a given Sentinel, is two
#   times the failover timeout.
#
# - The time needed for a slave replicating to a wrong master according
#   to a Sentinel current configuration, to be forced to replicate
#   with the right master, is exactly the failover timeout (counting since
#   the moment a Sentinel detected the misconfiguration).
#
# - The time needed to cancel a failover that is already in progress but
#   did not produced any configuration change (SLAVEOF NO ONE yet not
#   acknowledged by the promoted slave).
#
# - The maximum time a failover in progress waits for all the slaves to be
#   reconfigured as slaves of the new master. However even after this time
#   the slaves will be reconfigured by the Sentinels anyway, but not with
#   the exact parallel-syncs progression as specified.
# 如果在该时间（ms）内未能完成failover操作，则认为该failover失败
#
# Default is 3 minutes.
sentinel failover-timeout mymaster 180000

# SCRIPTS EXECUTION
#
# sentinel notification-script and sentinel reconfig-script are used in order
# to configure scripts that are called to notify the system administrator
# or to reconfigure clients after a failover. The scripts are executed
# with the following rules for error handling:
#
# If script exits with "1" the execution is retried later (up to a maximum
# number of times currently set to 10).
#
# If script exits with "2" (or an higher value) the script execution is
# not retried.
#
# If script terminates because it receives a signal the behavior is the same
# as exit code 1.
#
# A script has a maximum running time of 60 seconds. After this limit is
# reached the script is terminated with a SIGKILL and the execution retried.

# NOTIFICATION SCRIPT
#
# sentinel notification-script <master-name> <script-path>
# 
# Call the specified notification script for any sentinel event that is
# generated in the WARNING level (for instance -sdown, -odown, and so forth).
# This script should notify the system administrator via email, SMS, or any
# other messaging system, that there is something wrong with the monitored
# Redis systems.
#
# The script is called with just two arguments: the first is the event type
# and the second the event description.
#
# The script must exist and be executable in order for sentinel to start if
# this option is provided.
# 指定sentinel检测到该监控的redis实例指向的实例异常时，调用的报警脚本。该配置项可选，但是很常用。
#
# Example:
#
# sentinel notification-script mymaster /var/redis/notify.sh

# CLIENTS RECONFIGURATION SCRIPT
#
# sentinel client-reconfig-script <master-name> <script-path>
#
# When the master changed because of a failover a script can be called in
# order to perform application-specific tasks to notify the clients that the
# configuration has changed and the master is at a different address.
# 
# The following arguments are passed to the script:
#
# <master-name> <role> <state> <from-ip> <from-port> <to-ip> <to-port>
#
# <state> is currently always "failover"
# <role> is either "leader" or "observer"
# 
# The arguments from-ip, from-port, to-ip, to-port are used to communicate
# the old address of the master and the new address of the elected slave
# (now a master).
#
# This script should be resistant to multiple invocations.
#
# Example:
#
# sentinel client-reconfig-script mymaster /var/redis/reconfig.sh

-------------------------------------------------------------------------------------------------------------------------------

来自为知笔记(Wiz)