ftp服务安装和配置

#==========================
# Suse
zypper install vsftpd
service vsftpd start
service vsftpd status
# 配置文件路径
/etc/vsftpd.conf
/etc/ftpusers   # 不允许登陆的用户

#==========================
# Redhat/Centos
yum install vsftpd ftp -y
systemctl enable vsftpd
systemctl start vsftpd
systemctl status vsftpd
# 配置文件路径
/etc/vsftpd/vsftpd.conf
/etc/vsftpd/ftpusers   # 不允许登陆的用户
/etc/vsftpd/user_list  # 与userlist_deny参数配合使用,来控制登陆用户

#==========================
# 验证
ftp 127.0.0.1

#==========================
# windows免密登陆
ftp://user:[email protected]

suse初始配置
cat /etc/vsftpd.conf
# Example config file /etc/vsftpd.conf
#
# The default compiled in settings are fairly paranoid. This sample file
# loosens things up a bit, to make the ftp daemon more usable.
# Please see vsftpd.conf.5 for all compiled in defaults.
#
# If you do not change anything here you will have a minimum setup for an
# anonymus FTP server.
#
# READ THIS: This example file is NOT an exhaustive list of vsftpd options.
# Please read the vsftpd.conf.5 manual page to get a full idea of vsftpd‘s
# capabilities.

# General Settings
#
# Uncomment this to enable any form of FTP write command.
#
#write_enable=YES
#
# Activate directory messages - messages given to remote users when they
# go into a certain directory.
#
dirmessage_enable=YES
#
# It is recommended that you define on your system a unique user which the
# ftp server can use as a totally isolated and unprivileged user.
#
nopriv_user=ftpsecure
#
# You may fully customise the login banner string:
#
#ftpd_banner="Welcome to FOOBAR FTP service."
#
# You may activate the "-R" option to the builtin ls. This is disabled by
# default to avoid remote users being able to cause excessive I/O on large
# sites. However, some broken FTP clients such as "ncftp" and "mirror" assume
# the presence of the "-R" option, so there is a strong case for enabling it.
#
#ls_recurse_enable=YES
#
# You may specify a file of disallowed anonymous e-mail addresses. Apparently
# useful for combatting certain DoS attacks.
#
#deny_email_enable=YES
#
# (default follows)
#
#banned_email_file=/etc/vsftpd.banned_emails
#
# If  enabled,  all  user  and  group  information in
# directory listings will be displayed as "ftp".
#
#hide_ids=YES

# Local FTP user Settings
#
# Uncomment this to allow local users to log in.
#
local_enable=YES
#
# Default umask for local users is 077. You may wish to change this to 022,
# if your users expect that (022 is used by most other ftpd‘s)
#
#local_umask=022
#
# Uncomment to put local users in a chroot() jail in their home directory
# after login.
#
#chroot_local_user=YES
#
# You may specify an explicit list of local users to chroot() to their home
# directory. If chroot_local_user is YES, then this list becomes a list of
# users to NOT chroot().
#
#chroot_list_enable=YES
#
# (default follows)
#
#chroot_list_file=/etc/vsftpd.chroot_list
#
# The maximum data transfer rate permitted, in bytes per second, for
# local authenticated users. The default is 0 (unlimited).
#
#local_max_rate=7200

# Anonymus FTP user Settings
#
# Allow anonymous FTP?
#
anonymous_enable=YES
#
# Anonymous users will only be allowed to download files which are
# world readable.
#
anon_world_readable_only=YES
#
# Uncomment this to allow the anonymous FTP user to upload files. This only
# has an effect if the above global write enable is activated. Also, you will
# obviously need to create a directory writable by the FTP user.
#
#anon_upload_enable=YES
#
# Default umask for anonymus users is 077. You may wish to change this to 022,
# if your users expect that (022 is used by most other ftpd‘s)
#
#anon_umask=022
#
# Uncomment this if you want the anonymous FTP user to be able to create
# new directories.
#
#anon_mkdir_write_enable=YES
#
# Uncomment this to enable anonymus FTP users to perform other write operations
# like deletion and renaming.
#
#anon_other_write_enable=YES
#
# If you want, you can arrange for uploaded anonymous files to be owned by
# a different user. Note! Using "root" for uploaded files is not
# recommended!
#
#chown_uploads=YES
#chown_username=whoever
#
# The maximum data transfer rate permitted, in bytes per second, for anonymous
# authenticated users. The default is 0 (unlimited).
#
#anon_max_rate=7200

# Log Settings
#
# Log to the syslog daemon instead of using an logfile.
#
syslog_enable=YES
#
# Uncomment this to log all FTP requests and responses.
#
#log_ftp_protocol=YES
#
# Activate logging of uploads/downloads.
#
#xferlog_enable=YES
#

suse初始配置

centos初始配置
cat /etc/vsftpd/vsftpd.conf
# Example config file /etc/vsftpd/vsftpd.conf
#
# The default compiled in settings are fairly paranoid. This sample file
# loosens things up a bit, to make the ftp daemon more usable.
# Please see vsftpd.conf.5 for all compiled in defaults.
#
# READ THIS: This example file is NOT an exhaustive list of vsftpd options.
# Please read the vsftpd.conf.5 manual page to get a full idea of vsftpd‘s
# capabilities.
#
# Allow anonymous FTP? (Beware - allowed by default if you comment this out).
anonymous_enable=YES
#
# Uncomment this to allow local users to log in.
# When SELinux is enforcing check for SE bool ftp_home_dir
local_enable=YES
#
# Uncomment this to enable any form of FTP write command.
write_enable=YES
#
# Default umask for local users is 077. You may wish to change this to 022,
# if your users expect that (022 is used by most other ftpd‘s)
local_umask=022
#
# Uncomment this to allow the anonymous FTP user to upload files. This only
# has an effect if the above global write enable is activated. Also, you will
# obviously need to create a directory writable by the FTP user.
# When SELinux is enforcing check for SE bool allow_ftpd_anon_write, allow_ftpd_full_access
#anon_upload_enable=YES
#
# Uncomment this if you want the anonymous FTP user to be able to create
# new directories.
#anon_mkdir_write_enable=YES
#
# Activate directory messages - messages given to remote users when they
# go into a certain directory.
dirmessage_enable=YES
#
# Activate logging of uploads/downloads.
xferlog_enable=YES
#
# Make sure PORT transfer connections originate from port 20 (ftp-data).
connect_from_port_20=YES
#
# If you want, you can arrange for uploaded anonymous files to be owned by
# a different user. Note! Using "root" for uploaded files is not
# recommended!
#chown_uploads=YES
#chown_username=whoever
#
# You may override where the log file goes if you like. The default is shown
# below.
#xferlog_file=/var/log/xferlog
#
# If you want, you can have your log file in standard ftpd xferlog format.
# Note that the default log file location is /var/log/xferlog in this case.
xferlog_std_format=YES
#
# You may change the default value for timing out an idle session.
#idle_session_timeout=600
#
# You may change the default value for timing out a data connection.
#data_connection_timeout=120
#
# It is recommended that you define on your system a unique user which the
# ftp server can use as a totally isolated and unprivileged user.
#nopriv_user=ftpsecure
#
# Enable this and the server will recognise asynchronous ABOR requests. Not
# recommended for security (the code is non-trivial). Not enabling it,
# however, may confuse older FTP clients.
#async_abor_enable=YES
#
# By default the server will pretend to allow ASCII mode but in fact ignore
# the request. Turn on the below options to have the server actually do ASCII
# mangling on files when in ASCII mode.
# Beware that on some FTP servers, ASCII support allows a denial of service
# attack (DoS) via the command "SIZE /big/file" in ASCII mode. vsftpd
# predicted this attack and has always been safe, reporting the size of the
# raw file.
# ASCII mangling is a horrible feature of the protocol.
#ascii_upload_enable=YES
#ascii_download_enable=YES
#
# You may fully customise the login banner string:
#ftpd_banner=Welcome to blah FTP service.
#
# You may specify a file of disallowed anonymous e-mail addresses. Apparently
# useful for combatting certain DoS attacks.
#deny_email_enable=YES
# (default follows)
#banned_email_file=/etc/vsftpd/banned_emails
#
# You may specify an explicit list of local users to chroot() to their home
# directory. If chroot_local_user is YES, then this list becomes a list of
# users to NOT chroot().
# (Warning! chroot‘ing can be very dangerous. If using chroot, make sure that
# the user does not have write access to the top level directory within the
# chroot)
#chroot_local_user=YES
#chroot_list_enable=YES
# (default follows)
#chroot_list_file=/etc/vsftpd/chroot_list
#
# You may activate the "-R" option to the builtin ls. This is disabled by
# default to avoid remote users being able to cause excessive I/O on large
# sites. However, some broken FTP clients such as "ncftp" and "mirror" assume
# the presence of the "-R" option, so there is a strong case for enabling it.
#ls_recurse_enable=YES
#
# When "listen" directive is enabled, vsftpd runs in standalone mode and
# listens on IPv4 sockets. This directive cannot be used in conjunction
# with the listen_ipv6 directive.
listen=NO
#
# This directive enables listening on IPv6 sockets. By default, listening
# on the IPv6 "any" address (::) will accept connections from both IPv6
# and IPv4 clients. It is not necessary to listen on *both* IPv4 and IPv6
# sockets. If you want that (perhaps because you want to listen on specific
# addresses) then you must run two copies of vsftpd with two configuration
# files.
# Make sure, that one of the listen options is commented !!
listen_ipv6=YES

pam_service_name=vsftpd
userlist_enable=YES
tcp_wrappers=YES

centos初始配置

原文地址:https://www.cnblogs.com/sky58/p/9073588.html

时间: 2024-10-03 12:57:22

ftp服务安装和配置的相关文章

Linux FTP的安装与配置

Linux FTP的安装与配置 ftp安装部分,操作步骤如下: 可以使用yum命令直接安装ftp # yum install vsftpd ftp服务的开启与关闭命令: 开启:# service vsftpd start 关闭:# service vsftpd stop 安装成功后,可以在本地使用ftp软件连接,默认账号是虚拟机的账号和密码. 在linux中添加ftp用户,并设置相应的权限,操作步骤如下: 1.环境: ftp为vsftp 被限制用户名为test.被限制路径为/home/test

ubuntu FTP服务安装

//安装vsftp apt-get install vsftpd -y //增加账号 //1 查找 nologin位置 /usr/sbin/nologin useradd -d /alidata/www/wwwroot -s /sbin/nologin pwftp //2 设定密码 passwd pwftp //修改配置文件 vi /etc/vsftpd.conf //修改 anonymous_enable=NO //开启 local_enable=YES write_enable=YES ch

FTP服务搭建与配置

14.4 exportfs命令 exportfs命令用来管理当前NFS共享的文件系统列表. Options:-a:全部卸载或全部挂载-r:重新挂载-u:卸载某个目录-v:显示共享目录 常用组合: exportfs -arv服务端更改配置文件后,不重启服务,直接执行该命令就可以使更改后的配置文件生效. 注意: 在重启nfs服务之前需要先将所有挂载点卸载,否则将发生程序错误,严重者会拖垮系统. 以上操作均在服务端进行!!! 14.5 NFS客户端问题 针对NFS4版本在centos6中应用存在如下问

FTP服务安装与端口说明

FTP服务安装与端口说明 FTP端口安装部署windowswindows 2012 1. FTP服务介绍 1.1 什么是FTP 1.2 FTP服务端口 2 安装FTP服务器 2.1 添加服务器角色 2.2 安装类型选择 2.3 服务器选择 2.4 服务器角色选择 3 FTP站点搭建 3.1 添加FTP站点 3.1.1 从工具打开ISS管理器 3.1.2. 从网站选项,点击右侧的添加FTP站点 3.1.3. 填写站点名称和物理路径 3.2 FTP站点配置 3.2.1 ssl配置 3.2.2 身份验

[转帖]FTP服务搭建与配置

FTP服务搭建与配置 https://blog.csdn.net/zhengyshan/article/details/81058194 原作者写的很好.. 比我写的好一百倍.. 原创zhengyshan 发布于2018-07-15 22:52:06 阅读数 69 收藏展开 FTP介绍FTP是File Transfer Protocol(文件传输协议,简称文传协议)的英文简称,用于在Internet上控制文件的双向传输. FTP的主要作用就是让用户连接一个远程计算机(这些计算机上运行着FTP服务

【VNC】Linux环境VNC服务安装、配置与使用

[VNC]Linux环境VNC服务安装.配置与使用 2009-06-25 15:55:31 分类: Linux 前言:作为一名DBA,在创建Oracle数据库的过程中一般要使用dbca和netca图像化进行建库和创建监听(如果使用脚本建库另说),如果您身体好估计可以在瑟瑟发抖的机房中完成数据库的创建过程,由于本人对寒冷比较敏感,又不想通过这样的方式锻炼身体,所以更愿意在舒适的房间内一边品味着咖啡的浓香,顺便度过相对枯燥的数据库安装和配置的过程,So,图形化操作工具是必不可少的,在Linux操作系

CentOS 6.7 samba服务安装和配置

CentOS 6.7 samba服务安装和配置 Samba是在Linux和UNIX系统上实现SMB协议的一个免费软件,由服务器及客户端程序构成.SMB(Server Messages Block,信息服务块)是一种在局域网上共享文件和打印机的一种通信协议,它为局域网内的不同计算机之间提供文件及打印机等资源的共享服务. SMB是基于客户机/服务器型的协议,因而一台Samba服务器既可以充当文件共享服务器,也可以充当一个Samba的客户端,例如,一台在Linux 下已经架设好的Samba服务器,wi

Windows Server SNMP服务安装及配置

Windows Server SNMP服务安装及配置 一. Windows XP OR Windows Server2003 1. 安装服务 1) 打开控制面板,选择'添加或删除程序' 2) 点击左侧,'添加/删除Windows组件(A)' 3) 选择'管理和监视工具',并点击'详细信息' 4) 选择'简单网络管理协议(SNMP)',确定之后,点击下一步 5) 将SNMP所需要的文件准备好,点击浏览准备好的文件所在的文件夹,注意:该过程需要安装多个文件,所以请多次浏览文件所在的文件夹(需要准备:

linux服务安装与配置(二):安装xinetd服务

linux服务安装与配置(二):安装xinetd服务 xinetd即extended internet daemon,xinetd是新一代的网络守护进程服务程序,又叫超级Internet服务器.经常用来管理多种轻量级Internet服务.telnet服务就是通过xinetd服务来管理的,所以在安装后面telnet服务之前需要先安装xinetd服务. 首先查看是否有安装xinet服务: # rpm -qa | grep xinetd # 没有则使用光盘中rpm包来安装,步骤如下: # mkdir