Voice Lab 8-SIP笔记

H323 和SIP 的区别

SIP P2P : trunk

SIP C/S: end point

Sip拨号行为不支持kpml.每个按键就就发一次

默认sip电话只支持块输出,等拨dial的键才能发invite报文

但可以用sip dial rule去定义超时时间

Debug ccsip message

注意邦原:

Voice ser voip

Bind all source-interface f0/0

但r2直接dail-peer指到cucm不安全, 往往应该指到R1 CUBE

基于URI的路由是SIP route pattern 来配置的

怎么在cm中加域名:

Sip trunk security profile configuration===>sip trunk

Sip profile configuration===> sip end point

Ccm trace

时间： 2024-12-17 21:42:36

Voice Lab 8-SIP笔记的相关文章

Voice Lab 3-IPhone Features & CME Features

Voice Lab 3-IPhone Features & CME Features 1-试验拓扑: telephony-service no auto-reg-ephone //关闭自动注册 max-ephones 5 max-dn 5 ip source-address 192.168.100.1 port 2000 //电话注册地址 timeouts interdigit 5 //拨号按钮等待时间 system message HM TEST // 公司标示 network-locale

The Lab Renderer学习笔记

前言 Unity Vision VR/AR Summit来到中国了(http://www.bagevent.com/event/197605?bag_track=http://www.bagevent.com/event/197605 ),最近也关注了一下Unity的VR开发. 大概是6月份看到新闻:Steam发布了The Lab所使用的渲染器的所有源代码.我一直挺好奇的,对于Unity3D这样不开源的引擎,如果搞一个渲染器呢?今天有时间读一下代码,一探究竟. 相关链接: - 官方帖子:ht

Voice Lab 7- AAR-SRST-Media Resource

一集中式部署模型中的两个solution: 1-AAR,2-SRST 分布式模型没有这两个技术 1-AAR AAR 首先是发生在IP链路拥塞的情况下的,而SRST则是发生在IP链路中断的情况下 Regional : 放在不同的device pool,使用不同的编码 Location :配置带宽,让CM知道当前链路状态 Location的试验: 1-新建立一个'remote' location 我用1000--->2000 建立call,再用1001 ------->2001则不通,提示错误

voice lab2 – GK Operations

Voice Lab 2 –GK 1- GK e164 配置如下: R1(config)#int lo 0 R1(config-if)#ip add 1.1.1.1 255.255.255.255 R1(config-if)#no shut R1(config)#gatekeeper R1(config-gk)#zone local a cisco.com 1.1.1.1 R1(config-gk)#no shut R1(config)#int f0/1 R1(config-if)#h323-ga

Voice Lab6- CUCM2

Voice Lab CUCM2 1-路由类型总结分布式管理的缺陷是要FULL-MESH 2-CUCM部署模型拓扑图 2-1多站点分布式模型-用H323 Trunk建立站点间IP中继 R2的配置如下 R2(config)#int f0/1 R2(config-if)#h323-gateway voip bind srcaddr 192.168.200.254 //不敲这命令,CUCM会拒绝R2发起的call leg 2-2多站点分布式模型-用GK 控制的 H323 Trunk R1(confi

Lab 1-1

Lab 1-1 Questions and Short Answers Upload the files to http://www.VirusTotal.com/ and view the reports. Does either file match any existing antivirus signatures? A: These files were written specifically for this book, so as of this writing, you shou

Lab 3-3

Execute the malware found in the file Lab03-03.exe while monitoring it using basic dynamic analysis tools in a safe environment. Questions and Short Answers What do you notice when monitoring this malware with Process Explorer? A: The malware perform

Lab 6-1

LABS The goal of the labs for this chapter is to help you to understand the overall functionality of a program by analyzing code constructs. Each lab will guide you through discovering and analyzing a new code construct. Each lab builds on the previo

Lab 6-2

Analyze the malware found in the file Lab06-02.exe. Questions and Short Answers What operation does the first subroutine called by main perform? A: The first subroutine at 0x401000 is the same as in Lab 6-1. It's an if statement that checks for an ac