前几天收到 Arduino M0，试各项功能都正常，可就是串口监视器/串口助手不能显示程序里打印的输出，好生奇怪，各种换波特率各种PC串口程序换着试，资料不多，官方资料也只说到 Serial1 用于 pin 0 1 的（实际上测试的时候提示 Serial1 没有声明），Serial 用于 USB 通信，根本只字未提 SerialUSB 的事，直到今天，哦不，是昨天了，下午在群里提问，“忠忠”回复有一个 SerialUSB 用于 USB 的串口通信，这才知道了这个事。真是好坑人啊。
官网链接：http://www.arduino.org/products/boards/4-arduino-boards/arduino-m0
摘录：
Overview
With the new Arduino M0 board, the more creative individual will have the potential to create one’s most imaginative and new ideas for IoT devices, wearable technologies, high tech automation, wild robotics and other not yet thinkable adventures in the world of makers.
The
Arduino M0 represents a simple, yet powerful, 32-bit extension of the
Arduino UNO platform. The board is powered by Atmel’s SAMD21 MCU,
featuring a 32-bit ARM Cortex® M0 core.
With the addition of the M0 board, the Arduino family becomes larger with a new member providing increased performance.
The
power of its Atmel’s core gives this board an upgraded flexibility and
boosts the scope of projects one can think of and make; moreover, it
makes the M0 the ideal educational tool for learning about 32-bit
application development.
Summary
|
Microcontroller |
ATSAMD21G18, 48pins LQFP |
|
Operating Voltage |
3.3V |
|
Input Voltage (recommended) |
6-15 V |
|
Input Voltage (limits) |
4.5-20 V |
|
Digital I/O Pins |
14, with 12 PWM and UART |
|
Analog Input Pins |
6, 12-bit ADC channels |
|
Analog Output Pins |
1, 10-bit DAC |
|
DC Current per I/O Pin |
7 mA |
|
Flash Memory |
256 KB |
|
SRAM |
32 KB |
|
Clock Speed |
48 MHz |
Schematic & Reference Design
EAGLE files: arduino-M0-reference-design.zip
Schematic: arduino-M0-schematic.pdf
Power
The
Arduino M0 can be powered via the micro USB connection or with an
external power supply. The power source is selected automatically.
External
(non-USB) power can come either from an AC-to-DC adapter (wall-wart) or
battery. The adapter can be connected to the board by plugging a 2.1mm
center-positive plug into the board‘s power jack. Leads from a battery
can be inserted in the Gnd and Vin pin headers of the POWER connector.
The
board will automatically detect which power sources are available and
choose which one to use according to the following priority:
- External power
- Target USB
External
power is required when the 500mA through the USB connector is not
enough to power a connected USB device in a USB host application.
The power pins are as follows:
- VIN.
The input voltage to the Arduino board when it‘s using an external
power source (as opposed to 5 volts from the USB connection or other
regulated power source). You can supply voltage through this pin, or, if
supplying voltage via the power jack, access it through this pin. The allowed input voltage range for this pin (and for the power jack connector) is 6-20V. - 5V.
The regulated power supply used to power the microcontroller and other
components on the board. This can come either from VIN via an on-board
regulator, or be supplied by USB or another regulated 5V supply. The
maximum current output provided by the on-board regulator is 1A
(according to the power input source). - 3V3. A 3.3 volt supply generated by the on-board regulator. Maximum current draw is 1A (according to the power input source).
- GND. Ground pins.
- IOREF. The voltage at which the i/o pins of the board are operating (i.e. VCC for the board). This is 3.3V on the M0.
Memory
The ATSAMD21G18 has 256 KB of flash program memory (with 4 KB used for the bootloader). The
bootloader is factory pre burnt by Atmel and is stored in a dedicated
ROM memory. The bootloader is protected using the NVM fuse.
It also carries 32 KB of SRAM and up to 16KB by emulation of EEPROM (which can be read and written with the EEPROM library).
Input and Output
Each
of the 14 digital i/o pins on the M0 can be used as an input or output,
using pinMode(), digitalWrite(), and digitalRead() functions. They
operate at 3.3 volts. 7mA as maximum DC current for I/O pins and an
internal pull-up resistor (disconnected by default) of 20-60 kOhms. In
addition, some pins have specialized functions:
- Serial:
0 (RX) and 1 (TX). Used to receive (RX) and transmit (TX) TTL serial
data using the ATSAMD21G18 hardware serial capability. Note that on the
M0, the Serial class refers to USB (CDC) communication; for serial on
pins 0 and 1, use the Serial1 class. - TWI: SDA and SCL. Support TWI communication using the Wire library.
- PWM:
Pins 2 to 13 Provide 8-bit PWM output with the analogWrite() function.
The resolution of the PWM can be changed with the
analogWriteResolution() function.
Note1 The pins 4 and 10 can not be used simultaneously as PWM.
Note2 The pins 5 and 12 can not be used simultaneously as PWM. - SPI:
on the ICSP header. These pins support SPI communication using the SPI
library. Note that the SPI pins are not connected to any of the digital
I/O pins as they are on the Uno, They are only available on the ICSP
connector. This means that if you have a shield that uses SPI, but does
NOT have a 6-pin ICSP connector that connects to the M0‘s 6-pin ICSP
header, the shield will not work. - LED:
13. There is a built-in LED connected to digital pin 13. When the pin
is HIGH value, the LED is on, when the pin is LOW, it‘s off. - Analog Inputs:
A0-A5. The M0 has 6 analog inputs, labeled A0 through A5. Pins A0-A5
appear in the same locations as on the Uno; Each analog input provides
12 bits of resolution (i.e. 4096 different values). By default the
analog inputs measure from ground to 3.3 volts, though is it possible to
change the upper end of their range using the AREF pin and the
analogReference() function. - DAC:
pin A0 provides true analog outputs with 10-bits resolution (1023
levels) with the analogWrite() function. This pin can be used to create
an audio output using the Audio library. - Reset: Bring
this line LOW to reset the microcontroller. This is typically used to
add a reset button when shields are used that block the one already
present on the board.
Communication
The
Arduino M0 has a number of facilities for communicating with a
computer, with another Arduino or other microcontrollers, and with
different devices like phones, tablets, cameras and so on. The SAMD21 provides one hardware UART and three hardware USARTs for 3.3V serial communication.
The
Arduino software includes a serial monitor allowing simple textual data
to be sent to and from the board. The RX and TX LEDs on the board will
flash when data is being transmitted via the ATSAMD21G18 chip and USB connection to the computer (but not for serial communication on pins 0 and 1).
The
Native USB port is connected to the SAMD21. It allows for serial (CDC)
communication over USB. This provides a serial connection to the Serial
Monitor or other applications on your computer.
The
SAMD21 also supports TWI and SPI communication. The Arduino software
includes a Wire library to simplify use of the TWI bus. For SPI
communication, you can use the SPI library.
Programming
The Arduino M0 can be programmed with the Arduino software (download).
If you use Linux-based OS follow the guide Arduino IDE on Linux-based OS.
Uploading
sketches to the SAMD21 is different from how it works with the AVR
microcontrollers found in other Arduino boards: the flash memory needs
to be erased before being re-programmed. Upload operation is managed by a
dedicated ROM area on the SAMD21.
USB port:
To use this port, select "Arduino M0 (Native USB Port)" as your board
in the Arduino IDE. The Native USB port is connected directly to the
SAMD21. Connect the M0 Native USB port (the one closest to the reset
button) to your computer. Opening and closing the Native port at 1200bps
triggers a ‘soft erase‘ procedure: the flash memory is erased and the
board is restarted with the boot loader. Opening and closing the native
port at a different baudrate will not reset the SAMD21.
USB Overcurrent Protection
The
M0 has a resettable polyfuse that protects your computer‘s USB ports
from shorts and overcurrent. Although most computers provide their own
internal protection, the fuse provides an extra layer of protection. If
more than 500 mA flows through to the USB port, the fuse will
automatically break the connection until the short or overload is
removed.
Physical Characteristics
The
maximum length and width of the M0 PCB are 2.7 and 2.1 inches
respectively, with the USB connector and power jack extending beyond the
former dimension. Four screw holes allow the board to be attached to a
surface or case. Note that the distance between digital pins 7 and 8 is
160 mil (0.16"), not an even multiple of the 100 mil spacing of the
other pins.
Conformity Declaration
Product Code
A000103