硬件平台：OK6410开发板
KK
U-Boot 1.1.6 (Sep 19 2014 - 10:00:03) for SMDK6410
****************************************
** u-boot 1.1.6 **
** Updated for OK6410 TE6410 Board **
** Version (2012-09-23) **
** OEM: Forlinx Embedded **
** Web: http://www.witech.com.cn **
****************************************
CPU: S3C6410 @532MHz
Fclk = 532MHz, Hclk = 133MHz, Pclk = 66MHz, Serial = CLKUART (SYNC Mode)
Board: SMDK6410
DRAM: 256 MB
Flash: 0 kB
NAND: 1024 MB
In: serial
Out: serial
Err: serial
Hit any key to stop autoboot: 0
NAND read: device 0 offset 0x500000, size 0x500000
5242880 bytes read: OK
Boot with zImage
Starting kernel ...
Uncompressing Linux... done, booting the kernel.
Linux version 3.0.1 ([email protected]) (gcc version 4.3.2 (Sourcery G++ Lite 2008q3-72) ) #672 Mon May 11 16:13:51 CST 2015
CPU: ARMv6-compatible processor [410fb766] revision 6 (ARMv7), cr=00c5387f
CPU: VIPT nonaliasing data cache, VIPT nonaliasing instruction cache
Machine: SMDK6410
Ignoring unrecognised tag 0x54410008
Memory policy: ECC disabled, Data cache writeback
CPU S3C6410 (id 0x36410101)
s3c6410_init_clocks: initialising clocks
S3C24XX Clocks, Copyright 2004 Simtec Electronics
camera: no parent clock specified
s3c6400_setup_clocks: registering clocks
s3c6400_setup_clocks: clkdiv0 = 01043310
s3c6400_setup_clocks: xtal is 12000000
S3C64XX: PLL settings, A=532000000, M=532000000, E=24000000
S3C64XX: HCLK2=266000000, HCLK=133000000, PCLK=66500000
mout_apll: source is fout_apll (1), rate is 532000000
mout_epll: source is epll (1), rate is 24000000
mout_mpll: source is mpll (1), rate is 532000000
mmc_bus: source is mout_epll (0), rate is 24000000
mmc_bus: source is mout_epll (0), rate is 24000000
mmc_bus: source is mout_epll (0), rate is 24000000
usb-bus-host: source is clk_48m (0), rate is 48000000
s3c64xx_clk_doutmpll_get_rate: parent is 532000000
uclk1: source is dout_mpll (1), rate is 66500000
spi-bus: source is mout_epll (0), rate is 24000000
spi-bus: source is mout_epll (0), rate is 24000000
audio-bus: source is mout_epll (0), rate is 24000000
audio-bus: source is mout_epll (0), rate is 24000000
audio-bus: source is mout_epll (0), rate is 24000000
irda-bus: source is mout_epll (0), rate is 24000000
camera: no parent clock specified
s3c64xx: 15728640 bytes SDRAM reserved for fimc at 0x5f0f9000
s3c64xx: 8388608 bytes SDRAM reserved for pp at 0x5e8f9000
s3c64xx: 8388608 bytes SDRAM reserved for tv at 0x5e0f9000
s3c64xx: 6291456 bytes SDRAM reserved for mfc at 0x5daf9000
s3c64xx: 8388608 bytes SDRAM reserved for jpeg at 0x5d2f9000
s3c64xx: 8388608 bytes SDRAM reserved for cmm at 0x5caf9000
On node 0 totalpages: 65536
free_area_init_node: node 0, pgdat c0847c20, node_mem_map c08ce000
Normal zone: 512 pages used for memmap
Normal zone: 0 pages reserved
Normal zone: 65024 pages, LIFO batch:15
pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768
pcpu-alloc: [0] 0
Built 1 zonelists in Zone order, mobility grouping on. Total pages: 65024
Kernel command line: root=/dev/mtdblock2 rootfstype=yaffs2 init=/linuxrc console=ttySAC0,115200
PID hash table entries: 1024 (order: 0, 4096 bytes)
Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
Memory: 256MB = 256MB total
Memory: 196548k/196548k available, 65596k reserved, 0K highmem
Virtual kernel memory layout:
vector : 0xffff0000 - 0xffff1000 ( 4 kB)
fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB)
DMA : 0xff600000 - 0xffe00000 ( 8 MB)
vmalloc : 0xd0800000 - 0xf4000000 ( 568 MB)
lowmem : 0xc0000000 - 0xd0000000 ( 256 MB)
pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB)
modules : 0xbf000000 - 0xbfe00000 ( 14 MB)
.init : 0xc0008000 - 0xc0036000 ( 184 kB)
.text : 0xc0036000 - 0xc0800888 (7979 kB)
.data : 0xc0802000 - 0xc084af30 ( 292 kB)
.bss : 0xc084af54 - 0xc08cd554 ( 522 kB)
SLUB: Genslabs=13, HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
NR_IRQS:246 nr_irqs:246 246
s3c64xx_init_irq: initialising interrupts
VIC @f4000000: id 0x00041192, vendor 0x41
VIC @f4010000: id 0x00041192, vendor 0x41
timer tcon=00500000, tcnt 1b0f0, tcfg 00000200,00010000, usec 00001719
Console: colour dummy device 80x30
console [ttySAC0] enabled
Calibrating delay loop... 528.79 BogoMIPS (lpj=2643968)
pid_max: default: 32768 minimum: 301
Mount-cache hash table entries: 512
CPU: Testing write buffer coherency: ok
hw perfevents: enabled with v6 PMU driver, 3 counters available
devtmpfs: initialized
device: ‘platform‘: device_add
bus: ‘platform‘: registered
Registering sysdev class ‘cpu‘
Registering sysdev class ‘s3c64xx-core‘
Registering sys device of class ‘s3c64xx-core‘
Registering sys device ‘s3c64xx-core0‘
Registering sysdev class ‘s3c6410-core‘
NET: Registered protocol family 16
device class ‘bdi‘: registering
device class ‘tty‘: registering
device class ‘vtconsole‘: registering
device: ‘vtcon0‘: device_add
bus: ‘spi‘: registered
device class ‘spi_master‘: registering
bus: ‘i2c‘: registered
bus: ‘i2c‘: add driver dummy
Registering platform device ‘s3c-sdhci.0‘. Parent at platform
device: ‘s3c-sdhci.0‘: device_add
bus: ‘platform‘: add device s3c-sdhci.0
Registering platform device ‘s3c-sdhci.1‘. Parent at platform
device: ‘s3c-sdhci.1‘: device_add
bus: ‘platform‘: add device s3c-sdhci.1
Registering platform device ‘s3c2440-i2c.0‘. Parent at platform
device: ‘s3c2440-i2c.0‘: device_add
bus: ‘platform‘: add device s3c2440-i2c.0
Registering platform device ‘s3c-fb‘. Parent at platform
device: ‘s3c-fb‘: device_add
bus: ‘platform‘: add device s3c-fb
Registering platform device ‘s3c2410-ohci‘. Parent at platform
device: ‘s3c2410-ohci‘: device_add
bus: ‘platform‘: add device s3c2410-ohci
Registering platform device ‘s3c-hsotg‘. Parent at platform
device: ‘s3c-hsotg‘: device_add
bus: ‘platform‘: add device s3c-hsotg
Registering platform device ‘samsung-audio‘. Parent at platform
device: ‘samsung-audio‘: device_add
bus: ‘platform‘: add device samsung-audio
Registering platform device ‘s3c-keypad‘. Parent at platform
device: ‘s3c-keypad‘: device_add
bus: ‘platform‘: add device s3c-keypad
Registering platform device ‘gpio-keys‘. Parent at platform
device: ‘gpio-keys‘: device_add
bus: ‘platform‘: add device gpio-keys
Registering platform device ‘s3c6410-nand‘. Parent at platform
device: ‘s3c6410-nand‘: device_add
bus: ‘platform‘: add device s3c6410-nand
Registering platform device ‘dm9000.0‘. Parent at platform
device: ‘dm9000.0‘: device_add
bus: ‘platform‘: add device dm9000.0
Registering platform device ‘samsung-ac97‘. Parent at platform
device: ‘samsung-ac97‘: device_add
bus: ‘platform‘: add device samsung-ac97
Registering platform device ‘s3c64xx-rtc‘. Parent at platform
device: ‘s3c64xx-rtc‘: device_add
bus: ‘platform‘: add device s3c64xx-rtc
Registering platform device ‘s3c-ts‘. Parent at platform
device: ‘s3c-ts‘: device_add
bus: ‘platform‘: add device s3c-ts
Registering platform device ‘s3c-fimc.0‘. Parent at platform
device: ‘s3c-fimc.0‘: device_add
bus: ‘platform‘: add device s3c-fimc.0
Registering platform device ‘s3c-fimc.1‘. Parent at platform
device: ‘s3c-fimc.1‘: device_add
bus: ‘platform‘: add device s3c-fimc.1
Registering platform device ‘s3c2410-wdt‘. Parent at platform
device: ‘s3c2410-wdt‘: device_add
bus: ‘platform‘: add device s3c2410-wdt
Registering platform device ‘s3c-pp‘. Parent at platform
device: ‘s3c-pp‘: device_add
bus: ‘platform‘: add device s3c-pp
Registering platform device ‘s3c-mfc‘. Parent at platform
device: ‘s3c-mfc‘: device_add
bus: ‘platform‘: add device s3c-mfc
Registering platform device ‘s3c-tvenc‘. Parent at platform
device: ‘s3c-tvenc‘: device_add
bus: ‘platform‘: add device s3c-tvenc
Registering platform device ‘s3c-tvscaler‘. Parent at platform
device: ‘s3c-tvscaler‘: device_add
bus: ‘platform‘: add device s3c-tvscaler
Registering platform device ‘s3c-rotator‘. Parent at platform
device: ‘s3c-rotator‘: device_add
bus: ‘platform‘: add device s3c-rotator
Registering platform device ‘s3c-jpeg‘. Parent at platform
device: ‘s3c-jpeg‘: device_add
bus: ‘platform‘: add device s3c-jpeg
Registering platform device ‘s3c-g2d‘. Parent at platform
device: ‘s3c-g2d‘: device_add
bus: ‘platform‘: add device s3c-g2d
Registering platform device ‘s3c-g3d‘. Parent at platform
device: ‘s3c-g3d‘: device_add
bus: ‘platform‘: add device s3c-g3d
Registering platform device ‘s3c64xx-spi.0‘. Parent at platform
device: ‘s3c64xx-spi.0‘: device_add
bus: ‘platform‘: add device s3c64xx-spi.0
Registering platform device ‘s3c64xx-spi.1‘. Parent at platform
device: ‘s3c64xx-spi.1‘: device_add
bus: ‘platform‘: add device s3c64xx-spi.1
hw-breakpoint: found 6 breakpoint and 1 watchpoint registers.
hw-breakpoint: maximum watchpoint size is 4 bytes.
s3c64xx_dma_init: Registering DMA channels
Registering sysdev class ‘s3c64xx-dma‘
Registering sys device of class ‘s3c64xx-dma‘
Registering sys device ‘s3c64xx-dma0‘
PL080: IRQ 73, at d0804000, channels 0..8
Registering sys device of class ‘s3c64xx-dma‘
Registering sys device ‘s3c64xx-dma1‘
PL080: IRQ 74, at d0806000, channels 8..16
S3C6410: Initialising architecture
Registering sys device of class ‘s3c6410-core‘
Registering sys device ‘s3c6410-core0‘
Registering platform device ‘s3c6400-uart.0‘. Parent at platform
device: ‘s3c6400-uart.0‘: device_add
bus: ‘platform‘: add device s3c6400-uart.0
Registering platform device ‘s3c6400-uart.1‘. Parent at platform
device: ‘s3c6400-uart.1‘: device_add
bus: ‘platform‘: add device s3c6400-uart.1
Registering platform device ‘s3c6400-uart.2‘. Parent at platform
device: ‘s3c6400-uart.2‘: device_add
bus: ‘platform‘: add device s3c6400-uart.2
Registering platform device ‘s3c6400-uart.3‘. Parent at platform
device: ‘s3c6400-uart.3‘: device_add
bus: ‘platform‘: add device s3c6400-uart.3
bus: ‘platform‘: add driver s3c-adc
Registering sys device of class ‘cpu‘
Registering sys device ‘cpu0‘
device: ‘default‘: device_add
bio: create slab <bio-0> at 0
device class ‘block‘: registering
device class ‘graphics‘: registering
device class ‘misc‘: registering
device class ‘scsi_host‘: registering
bus: ‘scsi‘: registered
device class ‘scsi_device‘: registering
SCSI subsystem initialized
bus: ‘platform‘: add driver s3c64xx-spi
bus: ‘platform‘: driver_probe_device: matched device s3c64xx-spi.0 with driver s3c64xx-spi
bus: ‘platform‘: really_probe: probing driver s3c64xx-spi with device s3c64xx-spi.0
@@@@@@@@@@@@@@@@@@@@
s3c64xx_spi_probe 1111111111111111
@@@@@@@@@@@@@@@@@@@@
device: ‘spi0‘: device_add
s3c64xx-spi s3c64xx-spi.0: registered master spi0
s3c64xx-spi s3c64xx-spi.0: Samsung SoC SPI Driver loaded for Bus SPI-0 with 1 Slaves attached
s3c64xx-spi s3c64xx-spi.0: IOmem=[0x7f00b0ff-0x7f00b000] DMA=[Rx-13, Tx-12]
driver: ‘s3c64xx-spi.0‘: driver_bound: bound to device ‘s3c64xx-spi‘
bus: ‘platform‘: really_probe: bound device s3c64xx-spi.0 to driver s3c64xx-spi
bus: ‘platform‘: driver_probe_device: matched device s3c64xx-spi.1 with driver s3c64xx-spi
bus: ‘platform‘: really_probe: probing driver s3c64xx-spi with device s3c64xx-spi.1
@@@@@@@@@@@@@@@@@@@@
s3c64xx_spi_probe 1111111111111111
@@@@@@@@@@@@@@@@@@@@
device: ‘spi1‘: device_add
s3c64xx-spi s3c64xx-spi.1: registered master spi1
------------[ cut here ]------------
WARNING: at drivers/gpio/gpiolib.c:101 gpio_ensure_requested+0x58/0x124()
autorequest GPIO-24
Modules linked in:
[<c003cca8>] (unwind_backtrace+0x0/0xfc) from [<c05677e4>] (dump_stack+0x18/0x1c)
[<c05677e4>] (dump_stack+0x18/0x1c) from [<c0052840>] (warn_slowpath_common+0x54/0x6c)
[<c0052840>] (warn_slowpath_common+0x54/0x6c) from [<c00528fc>] (warn_slowpath_fmt+0x38/0x40)
[<c00528fc>] (warn_slowpath_fmt+0x38/0x40) from [<c0210490>] (gpio_ensure_requested+0x58/0x124)
[<c0210490>] (gpio_ensure_requested+0x58/0x124) from [<c02106ac>] (gpio_direction_output+0x84/0x1a0)
[<c02106ac>] (gpio_direction_output+0x84/0x1a0) from [<c0044cb0>] (cs_set_level+0x10/0x14)
[<c0044cb0>] (cs_set_level+0x10/0x14) from [<c02787d8>] (s3c64xx_spi_setup+0x10c/0x1f8)
[<c02787d8>] (s3c64xx_spi_setup+0x10c/0x1f8) from [<c0276b88>] (spi_setup+0x60/0x114)
[<c0276b88>] (spi_setup+0x60/0x114) from [<c0276ef4>] (spi_add_device+0x98/0x150)
[<c0276ef4>] (spi_add_device+0x98/0x150) from [<c0277028>] (spi_new_device+0x7c/0xb4)
[<c0277028>] (spi_new_device+0x7c/0xb4) from [<c0277088>] (spi_match_master_to_boardinfo+0x28/0x48)
[<c0277088>] (spi_match_master_to_boardinfo+0x28/0x48) from [<c02771a4>] (spi_register_master+0xfc/0x164)
[<c02771a4>] (spi_register_master+0xfc/0x164) from [<c0021b14>] (s3c64xx_spi_probe+0x42c/0x540)
[<c0021b14>] (s3c64xx_spi_probe+0x42c/0x540) from [<c02484f8>] (platform_drv_probe+0x20/0x24)
[<c02484f8>] (platform_drv_probe+0x20/0x24) from [<c02470fc>] (driver_probe_device+0xe0/0x238)
[<c02470fc>] (driver_probe_device+0xe0/0x238) from [<c02472e8>] (__driver_attach+0x94/0x98)
[<c02472e8>] (__driver_attach+0x94/0x98) from [<c0246824>] (bus_for_each_dev+0x68/0x94)
[<c0246824>] (bus_for_each_dev+0x68/0x94) from [<c0246ea8>] (driver_attach+0x20/0x28)
[<c0246ea8>] (driver_attach+0x20/0x28) from [<c0245ff8>] (bus_add_driver+0xd4/0x274)
[<c0245ff8>] (bus_add_driver+0xd4/0x274) from [<c02476e4>] (driver_register+0x74/0x15c)
[<c02476e4>] (driver_register+0x74/0x15c) from [<c02487e4>] (platform_driver_register+0x4c/0x60)
[<c02487e4>] (platform_driver_register+0x4c/0x60) from [<c0248818>] (platform_driver_probe+0x20/0x6c)
[<c0248818>] (platform_driver_probe+0x20/0x6c) from [<c00216dc>] (s3c64xx_spi_init+0x18/0x24)
[<c00216dc>] (s3c64xx_spi_init+0x18/0x24) from [<c00363c8>] (do_one_initcall+0x3c/0x188)
[<c00363c8>] (do_one_initcall+0x3c/0x188) from [<c000845c>] (kernel_init+0x88/0x130)
[<c000845c>] (kernel_init+0x88/0x130) from [<c0037a34>] (kernel_thread_exit+0x0/0x8)
---[ end trace da227214a82491b7 ]---
spi spi1.0: setup mode 0, 8 bits/w, 8312500 Hz max --> 0
@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@
setup status = 0
@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@
device: ‘spi1.0‘: device_add
bus: ‘spi‘: add device spi1.0
s3c64xx-spi s3c64xx-spi.1: registered child spi1.0
s3c64xx-spi s3c64xx-spi.1: Samsung SoC SPI Driver loaded for Bus SPI-1 with 1 Slaves attached
s3c64xx-spi s3c64xx-spi.1: IOmem=[0x7f00c0ff-0x7f00c000] DMA=[Rx-21, Tx-20]
driver: ‘s3c64xx-spi.1‘: driver_bound: bound to device ‘s3c64xx-spi‘
bus: ‘platform‘: really_probe: bound device s3c64xx-spi.1 to driver s3c64xx-spi
device class ‘mdio_bus‘: registering
bus: ‘mdio_bus‘: registered
bus: ‘mdio_bus‘: add driver Generic PHY
bus: ‘usb‘: registered
bus: ‘usb‘: add driver usbfs
usbcore: registered new interface driver usbfs
device class ‘usb_device‘: registering
bus: ‘usb‘: add driver hub
usbcore: registered new interface driver hub
bus: ‘usb‘: add driver usb
usbcore: registered new device driver usb
bus: ‘serio‘: registered
device class ‘input‘: registering
device class ‘rtc‘: registering
bus: ‘platform‘: add driver s3c-i2c
bus: ‘platform‘: driver_probe_device: matched device s3c2440-i2c.0 with driver s3c-i2c
bus: ‘platform‘: really_probe: probing driver s3c-i2c with device s3c2440-i2c.0
s3c-i2c s3c2440-i2c.0: slave address 0x10
s3c-i2c s3c2440-i2c.0: bus frequency set to 64 KHz
device: ‘i2c-0‘: device_add
bus: ‘i2c‘: add device i2c-0
device: ‘0-0050‘: device_add
bus: ‘i2c‘: add device 0-0050
device: ‘0-001b‘: device_add
bus: ‘i2c‘: add device 0-001b
device: ‘0-0030‘: device_add
bus: ‘i2c‘: add device 0-0030
s3c-i2c s3c2440-i2c.0: i2c-0: S3C I2C adapter
driver: ‘s3c2440-i2c.0‘: driver_bound: bound to device ‘s3c-i2c‘
bus: ‘platform‘: really_probe: bound device s3c2440-i2c.0 to driver s3c-i2c
bus: ‘mmc‘: registered
device class ‘mmc_host‘: registering
bus: ‘sdio‘: registered
device class ‘leds‘: registering
device class ‘sound‘: registering
Advanced Linux Sound Architecture Driver Version 1.0.23.
bus: ‘ac97‘: registered
device class ‘net‘: registering
device: ‘lo‘: device_add
Bluetooth: Core ver 2.16
device class ‘bluetooth‘: registering
NET: Registered protocol family 31
Bluetooth: HCI device and connection manager initialized
Bluetooth: HCI socket layer initialized
Bluetooth: L2CAP socket layer initialized
Bluetooth: SCO socket layer initialized
device class ‘ieee80211‘: registering
Registering platform device ‘regulatory.0‘. Parent at platform
device: ‘regulatory.0‘: device_add
bus: ‘platform‘: add device regulatory.0
cfg80211: Calling CRDA to update world regulatory domain
device class ‘rfkill‘: registering
device: ‘rfkill‘: device_add
device class ‘mem‘: registering
device: ‘mem‘: device_add
device: ‘null‘: device_add
device: ‘zero‘: device_add
device: ‘full‘: device_add
device: ‘random‘: device_add
device: ‘urandom‘: device_add
device: ‘kmsg‘: device_add
device: ‘tty‘: device_add
device: ‘console‘: device_add
device: ‘tty0‘: device_add
device class ‘vc‘: registering
device: ‘vcs‘: device_add
device: ‘vcsa‘: device_add
device: ‘vcs1‘: device_add
device: ‘vcsa1‘: device_add
device: ‘tty1‘: device_add
device: ‘tty2‘: device_add
device: ‘tty3‘: device_add
device: ‘tty4‘: device_add
device: ‘tty5‘: device_add
device: ‘tty6‘: device_add
device: ‘tty7‘: device_add
device: ‘tty8‘: device_add
device: ‘tty9‘: device_add
device: ‘tty10‘: device_add
device: ‘tty11‘: device_add
device: ‘tty12‘: device_add
device: ‘tty13‘: device_add
device: ‘tty14‘: device_add
device: ‘tty15‘: device_add
device: ‘tty16‘: device_add
device: ‘tty17‘: device_add
device: ‘tty18‘: device_add
device: ‘tty19‘: device_add
device: ‘tty20‘: device_add
device: ‘tty21‘: device_add
device: ‘tty22‘: device_add
device: ‘tty23‘: device_add
device: ‘tty24‘: device_add
device: ‘tty25‘: device_add
device: ‘tty26‘: device_add
device: ‘tty27‘: device_add
device: ‘tty28‘: device_add
device: ‘tty29‘: device_add
device: ‘tty30‘: device_add
device: ‘tty31‘: device_add
device: ‘tty32‘: device_add
device: ‘tty33‘: device_add
device: ‘tty34‘: device_add
device: ‘tty35‘: device_add
device: ‘tty36‘: device_add
device: ‘tty37‘: device_add
device: ‘tty38‘: device_add
device: ‘tty39‘: device_add
device: ‘tty40‘: device_add
device: ‘tty41‘: device_add
device: ‘tty42‘: device_add
device: ‘tty43‘: device_add
device: ‘tty44‘: device_add
device: ‘tty45‘: device_add
device: ‘tty46‘: device_add
device: ‘tty47‘: device_add
device: ‘tty48‘: device_add
device: ‘tty49‘: device_add
device: ‘tty50‘: device_add
device: ‘tty51‘: device_add
device: ‘tty52‘: device_add
device: ‘tty53‘: device_add
device: ‘tty54‘: device_add
device: ‘tty55‘: device_add
device: ‘tty56‘: device_add
device: ‘tty57‘: device_add
device: ‘tty58‘: device_add
device: ‘tty59‘: device_add
device: ‘tty60‘: device_add
device: ‘tty61‘: device_add
device: ‘tty62‘: device_add
device: ‘tty63‘: device_add
device class ‘firmware‘: registering
NET: Registered protocol family 2
IP route cache hash table entries: 2048 (order: 1, 8192 bytes)
TCP established hash table entries: 8192 (order: 4, 65536 bytes)
TCP bind hash table entries: 8192 (order: 3, 32768 bytes)
TCP: Hash tables configured (established 8192 bind 8192)
TCP reno registered
UDP hash table entries: 256 (order: 0, 4096 bytes)
UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
NET: Registered protocol family 1
RPC: Registered named UNIX socket transport module.
RPC: Registered udp transport module.
RPC: Registered tcp transport module.
RPC: Registered tcp NFSv4.1 backchannel transport module.
bus: ‘platform‘: add driver arm-pmu
Registering sysdev class ‘clocksource‘
Registering sys device of class ‘clocksource‘
Registering sys device ‘clocksource0‘
bus: ‘platform‘: add driver alarmtimer
Registering platform device ‘alarmtimer‘. Parent at platform
device: ‘alarmtimer‘: device_add
bus: ‘platform‘: add device alarmtimer
bus: ‘platform‘: driver_probe_device: matched device alarmtimer with driver alarmtimer
bus: ‘platform‘: really_probe: probing driver alarmtimer with device alarmtimer
driver: ‘alarmtimer‘: driver_bound: bound to device ‘alarmtimer‘
bus: ‘platform‘: really_probe: bound device alarmtimer to driver alarmtimer
audit: initializing netlink socket (disabled)
type=2000 audit(1.290:1): initialized
bus: ‘event_source‘: registered
device: ‘cpu‘: device_add
bus: ‘event_source‘: add device cpu
device: ‘breakpoint‘: device_add
bus: ‘event_source‘: add device breakpoint
device: ‘tracepoint‘: device_add
bus: ‘event_source‘: add device tracepoint
device: ‘software‘: device_add
bus: ‘event_source‘: add device software
yaffs: yaffs built May 11 2015 16:02:03 Installing.
msgmni has been set to 383
alg: No test for stdrng (krng)
device class ‘bsg‘: registering
Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253)
io scheduler noop registered
io scheduler deadline registered
io scheduler cfq registered (default)
device: ‘fbcon‘: device_add
bus: ‘platform‘: add driver s3c-fb
bus: ‘platform‘: driver_probe_device: matched device s3c-fb with driver s3c-fb
bus: ‘platform‘: really_probe: probing driver s3c-fb with device s3c-fb
S3C_LCD clock got enabled :: 133.000 Mhz
LCD TYPE :: LTE480WV will be initialized
Window[0] - FB1: map_video_memory: clear ffd80000:0007f800
FB1: map_video_memory: dma=5c580000 cpu=ffd80000 size=0007f800
Window[0] - FB2: map_video_memory: clear ffdbfc00:0003fc00
FB2: map_video_memory: dma=5c5bfc00 cpu=ffdbfc00 size=0003fc00
device: ‘fb0‘: device_add
device: ‘vtcon1‘: device_add
Console: switching to colour frame buffer device 60x34
fb0: s3cfb frame buffer device
Window[1] - FB1: map_video_memory: clear ffd40000:0003fc00
FB1: map_video_memory: dma=5c600000 cpu=ffd40000 size=0003fc00
Window[1] - FB2: map_video_memory: clear ffd5fe00:0001fe00
FB2: map_video_memory: dma=5c61fe00 cpu=ffd5fe00 size=0001fe00
device: ‘fb1‘: device_add
fb1: s3cfb frame buffer device
Window[2] - FB1: map_video_memory: clear ffd00000:0003fc00
FB1: map_video_memory: dma=5c640000 cpu=ffd00000 size=0003fc00
device: ‘fb2‘: device_add
fb2: s3cfb frame buffer device
Window[3] - FB1: map_video_memory: clear ffcc0000:0003fc00
FB1: map_video_memory: dma=5c680000 cpu=ffcc0000 size=0003fc00
device: ‘fb3‘: device_add
fb3: s3cfb frame buffer device
driver: ‘s3c-fb‘: driver_bound: bound to device ‘s3c-fb‘
bus: ‘platform‘: really_probe: bound device s3c-fb to driver s3c-fb
device: ‘ptmx‘: device_add
bus: ‘platform‘: add driver s3c6400-uart
bus: ‘platform‘: driver_probe_device: matched device s3c6400-uart.0 with driver s3c6400-uart
bus: ‘platform‘: really_probe: probing driver s3c6400-uart with device s3c6400-uart.0
s3c6400-uart.0: ttySAC0 at MMIO 0x7f005000 (irq = 16) is a S3C6400/10
device: ‘ttySAC0‘: device_add
driver: ‘s3c6400-uart.0‘: driver_bound: bound to device ‘s3c6400-uart‘
bus: ‘platform‘: really_probe: bound device s3c6400-uart.0 to driver s3c6400-uart
bus: ‘platform‘: driver_probe_device: matched device s3c6400-uart.1 with driver s3c6400-uart
bus: ‘platform‘: really_probe: probing driver s3c6400-uart with device s3c6400-uart.1
s3c6400-uart.1: ttySAC1 at MMIO 0x7f005400 (irq = 20) is a S3C6400/10
device: ‘ttySAC1‘: device_add
driver: ‘s3c6400-uart.1‘: driver_bound: bound to device ‘s3c6400-uart‘
bus: ‘platform‘: really_probe: bound device s3c6400-uart.1 to driver s3c6400-uart
bus: ‘platform‘: driver_probe_device: matched device s3c6400-uart.2 with driver s3c6400-uart
bus: ‘platform‘: really_probe: probing driver s3c6400-uart with device s3c6400-uart.2
s3c6400-uart.2: ttySAC2 at MMIO 0x7f005800 (irq = 24) is a S3C6400/10
device: ‘ttySAC2‘: device_add
driver: ‘s3c6400-uart.2‘: driver_bound: bound to device ‘s3c6400-uart‘
bus: ‘platform‘: really_probe: bound device s3c6400-uart.2 to driver s3c6400-uart
bus: ‘platform‘: driver_probe_device: matched device s3c6400-uart.3 with driver s3c6400-uart
bus: ‘platform‘: really_probe: probing driver s3c6400-uart with device s3c6400-uart.3
s3c6400-uart.3: ttySAC3 at MMIO 0x7f005c00 (irq = 28) is a S3C6400/10
device: ‘ttySAC3‘: device_add
driver: ‘s3c6400-uart.3‘: driver_bound: bound to device ‘s3c6400-uart‘
bus: ‘platform‘: really_probe: bound device s3c6400-uart.3 to driver s3c6400-uart
device: ‘leds‘: device_add
device: ‘pwm‘: device_add
pwm initialized
adc herr
device: ‘adc‘: device_add
adc initialized
device class ‘tem_class‘: registering
device: ‘tem0‘: device_add
@@@@@@@@@@@@@@@@@@@@@@@@@@
Tem initialized
@@@@@@@@@@@@@@@@@@@@@@@@@@
Hello, world
device class ‘irda_class‘: registering
device: ‘irda0‘: device_add
@@@@@@@@@@@@@@@@@@@@@@@@@@
irda initialized
@@@@@@@@@@@@@@@@@@@@@@@@@@
@@@@@@@@@@@
tmp = 0
@@@@@@@@@@@
device: ‘rs485io‘: device_add
device class ‘scsi_disk‘: registering
bus: ‘scsi‘: add driver sd
device class ‘scsi_generic‘: registering
device class ‘mtd‘: registering
device: ‘mtd-unmap‘: device_add
device: ‘mtd-romap‘: device_add
device: ‘mtd-rwmap‘: device_add
S3C NAND Driver, (c) 2008 Samsung Electronics
bus: ‘platform‘: add driver s3c2450-nand
bus: ‘platform‘: add driver s3c6400-nand
bus: ‘platform‘: add driver s3c6410-nand
bus: ‘platform‘: driver_probe_device: matched device s3c6410-nand with driver s3c6410-nand
bus: ‘platform‘: really_probe: probing driver s3c6410-nand with device s3c6410-nand
NandFlash is busying.........
forlinx nandflash dev_id=38
forlinx******Nandflash:ChipType= SLC ChipName=MT29F8G08ABABAWP
S3C NAND Driver is using hardware ECC.
NAND device: Manufacturer ID: 0x2c, Chip ID: 0x38 (Micron NAND 2GiB 1,8V 8-bit)
Creating 4 MTD partitions on "NAND 2GiB 1,8V 8-bit":
0x000000000000-0x000000200000 : "Bootloader"
device: ‘mtd0‘: device_add
device: ‘mtd0ro‘: device_add
device: ‘31:0‘: device_add
device: ‘mtdblock0‘: device_add
0x000000500000-0x000001e00000 : "Kernel"
device: ‘mtd1‘: device_add
device: ‘mtd1ro‘: device_add
device: ‘31:1‘: device_add
device: ‘mtdblock1‘: device_add
0x000001e00000-0x00000e600000 : "File System"
device: ‘mtd2‘: device_add
device: ‘mtd2ro‘: device_add
device: ‘31:2‘: device_add
device: ‘mtdblock2‘: device_add
0x00000e600000-0x000040000000 : "User"
device: ‘mtd3‘: device_add
device: ‘mtd3ro‘: device_add
device: ‘31:3‘: device_add
device: ‘mtdblock3‘: device_add
driver: ‘s3c6410-nand‘: driver_bound: bound to device ‘s3c6410-nand‘
bus: ‘platform‘: really_probe: bound device s3c6410-nand to driver s3c6410-nand
bus: ‘platform‘: add driver s5pc100-nand
bus: ‘platform‘: add driver gen_nand
bus: ‘platform‘: add driver spi_gpio
bus: ‘platform‘: remove driver spi_gpio
driver: ‘spi_gpio‘: driver_release
device class ‘spidev‘: registering
bus: ‘spi‘: add driver spidev
vcan: Virtual CAN interface driver
slcan: serial line CAN interface driver
slcan: 10 dynamic interface channels.
CAN device driver interface
bus: ‘spi‘: add driver mcp2515
bus: ‘spi‘: driver_probe_device: matched device spi1.0 with driver mcp2515
bus: ‘spi‘: really_probe: probing driver mcp2515 with device spi1.0
@@@@@@@@@@@@@@@@@@@@
mcp251x probe 1111111111111111
@@@@@@@@@@@@@@@@@@@@
mcp251x: setup gpio pins CS and External Int
mcp2515 spi1.0: setup mode 0, 8 bits/w, 8312500 Hz max --> 0
@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@
setup status = 0
@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@
mcp2515 spi1.0: MCP251x didn‘t enter in conf mode after reset
mcp2515 spi1.0: CANSTAT 0xee CANCTRL 0x17
mcp2515 spi1.0: Probe failed
mcp2515 spi1.0: probe failed
PPP generic driver version 2.4.2
device class ‘ppp‘: registering
device: ‘ppp‘: device_add
PPP Deflate Compression module registered
PPP BSD Compression module registered
PPP MPPE Compression module registered
NET: Registered protocol family 24
dm9000 Ethernet Driver, V2.6.31
bus: ‘platform‘: add driver dm9000
bus: ‘platform‘: driver_probe_device: matched device dm9000.0 with driver dm9000
bus: ‘platform‘: really_probe: probing driver dm9000 with device dm9000.0
[dm9] dm9000_probe ndev->irq=6c
[dm9].1 read id 0x01010101
dm9000 dm9000.0: read wrong id 0x01010101
[dm9].2 read id 0x90000a46
[dm9000 Ethernet Driver, V2.6.31]: KV= 3.0.1 !!
[dm9000 Ethernet Driver, V2.6.31]: ChipID= 0x90000a46 !!
[DM9000]dm9000 revision 0x19
device: ‘eth0‘: device_add
eth0: dm9000a at d081c000,d0c00004 IRQ 108 MAC: 08:90:00:a0:90:90 (platform data)
driver: ‘dm9000.0‘: driver_bound: bound to device ‘dm9000‘
bus: ‘platform‘: really_probe: bound device dm9000.0 to driver dm9000
RTL871X: module init start version:v4.1.7_9024.20130916
RTL871X: rtl8189es driver version=v4.1.7_9024.20130916
RTL871X: build time: May 11 2015 16:06:40
bus: ‘sdio‘: add driver rtl8189es
RTL871X: module init ret=0
libertas_sdio: Libertas SDIO driver
libertas_sdio: Copyright Pierre Ossman
bus: ‘sdio‘: add driver libertas_sdio
ohci_hcd: USB 1.1 ‘Open‘ Host Controller (OHCI) Driver
bus: ‘platform‘: add driver s3c2410-ohci
bus: ‘platform‘: driver_probe_device: matched device s3c2410-ohci with driver s3c2410-ohci
bus: ‘platform‘: really_probe: probing driver s3c2410-ohci with device s3c2410-ohci
gjl usb_hcd_s3c2410_probe here 000!
gjl usb_hcd_s3c2410_probe here 11111!
s3c2410-ohci s3c2410-ohci: S3C24XX OHCI
s3c2410-ohci s3c2410-ohci: new USB bus registered, assigned bus number 1
s3c2410-ohci s3c2410-ohci: irq 79, io mem 0x74300000
gjl ohci_init here 000!
usb usb1: New USB device found, idVendor=1d6b, idProduct=0001
usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb1: Product: S3C24XX OHCI
usb usb1: Manufacturer: Linux 3.0.1 ohci_hcd
usb usb1: SerialNumber: s3c24xx
device: ‘usb1‘: device_add
bus: ‘usb‘: add device usb1
bus: ‘usb‘: driver_probe_device: matched device usb1 with driver usb
bus: ‘usb‘: really_probe: probing driver usb with device usb1
device: ‘1-0:1.0‘: device_add
bus: ‘usb‘: add device 1-0:1.0
bus: ‘usb‘: driver_probe_device: matched device 1-0:1.0 with driver hub
bus: ‘usb‘: really_probe: probing driver hub with device 1-0:1.0
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
driver: ‘1-0:1.0‘: driver_bound: bound to device ‘hub‘
bus: ‘usb‘: really_probe: bound device 1-0:1.0 to driver hub
device: ‘ep_81‘: device_add
device: ‘usbdev1.1‘: device_add
driver: ‘usb1‘: driver_bound: bound to device ‘usb‘
bus: ‘usb‘: really_probe: bound device usb1 to driver usb
device: ‘ep_00‘: device_add
driver: ‘s3c2410-ohci‘: driver_bound: bound to device ‘s3c2410-ohci‘
bus: ‘platform‘: really_probe: bound device s3c2410-ohci to driver s3c2410-ohci
bus: ‘usb‘: add driver cdc_acm
usbcore: registered new interface driver cdc_acm
cdc_acm: USB Abstract Control Model driver for USB modems and ISDN adapters
Initializing USB Mass Storage driver...
bus: ‘usb‘: add driver usb-storage
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
bus: ‘usb-serial‘: registered
bus: ‘usb‘: add driver usbserial
usbcore: registered new interface driver usbserial
bus: ‘usb-serial‘: add driver generic
USB Serial support registered for generic
bus: ‘usb‘: add driver usbserial_generic
usbcore: registered new interface driver usbserial_generic
usbserial: USB Serial Driver core
bus: ‘usb-serial‘: add driver option1
USB Serial support registered for GSM modem (1-port)
bus: ‘usb‘: add driver option
usbcore: registered new interface driver option
option: v0.7.2:USB Driver for GSM modems
bus: ‘usb-serial‘: add driver pl2303
USB Serial support registered for pl2303
bus: ‘usb‘: add driver pl2303
usbcore: registered new interface driver pl2303
pl2303: Prolific PL2303 USB to serial adaptor driver
bus: ‘platform‘: add driver dummy_hcd
bus: ‘platform‘: add driver dummy_udc
Registering platform device ‘dummy_hcd‘. Parent at platform
device: ‘dummy_hcd‘: device_add
bus: ‘platform‘: add device dummy_hcd
bus: ‘platform‘: driver_probe_device: matched device dummy_hcd with driver dummy_hcd
bus: ‘platform‘: really_probe: probing driver dummy_hcd with device dummy_hcd
dummy_hcd dummy_hcd: USB Host+Gadget Emulator, driver 02 May 2005
dummy_hcd dummy_hcd: Dummy host controller
dummy_hcd dummy_hcd: new USB bus registered, assigned bus number 2
usb usb2: New USB device found, idVendor=1d6b, idProduct=0002
usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb2: Product: Dummy host controller
usb usb2: Manufacturer: Linux 3.0.1 dummy_hcd
usb usb2: SerialNumber: dummy_hcd
device: ‘usb2‘: device_add
bus: ‘usb‘: add device usb2
bus: ‘usb‘: driver_probe_device: matched device usb2 with driver usb
bus: ‘usb‘: really_probe: probing driver usb with device usb2
device: ‘2-0:1.0‘: device_add
bus: ‘usb‘: add device 2-0:1.0
bus: ‘usb‘: driver_probe_device: matched device 2-0:1.0 with driver hub
bus: ‘usb‘: really_probe: probing driver hub with device 2-0:1.0
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 1 port detected
driver: ‘2-0:1.0‘: driver_bound: bound to device ‘hub‘
bus: ‘usb‘: really_probe: bound device 2-0:1.0 to driver hub
device: ‘ep_81‘: device_add
device: ‘usbdev2.1‘: device_add
driver: ‘usb2‘: driver_bound: bound to device ‘usb‘
bus: ‘usb‘: really_probe: bound device usb2 to driver usb
device: ‘ep_00‘: device_add
driver: ‘dummy_hcd‘: driver_bound: bound to device ‘dummy_hcd‘
bus: ‘platform‘: really_probe: bound device dummy_hcd to driver dummy_hcd
Registering platform device ‘dummy_udc‘. Parent at platform
device: ‘dummy_udc‘: device_add
bus: ‘platform‘: add device dummy_udc
bus: ‘platform‘: driver_probe_device: matched device dummy_udc with driver dummy_udc
bus: ‘platform‘: really_probe: probing driver dummy_udc with device dummy_udc
device: ‘gadget‘: device_add
driver: ‘dummy_udc‘: driver_bound: bound to device ‘dummy_udc‘
bus: ‘platform‘: really_probe: bound device dummy_udc to driver dummy_udc
device: ‘mice‘: device_add
mousedev: PS/2 mouse device common for all mice
bus: ‘platform‘: add driver gpio-keys
bus: ‘platform‘: driver_probe_device: matched device gpio-keys with driver gpio-keys
bus: ‘platform‘: really_probe: probing driver gpio-keys with device gpio-keys
device: ‘input0‘: device_add
input: gpio-keys as /devices/platform/gpio-keys/input/input0
device: ‘event0‘: device_add
driver: ‘gpio-keys‘: driver_bound: bound to device ‘gpio-keys‘
bus: ‘platform‘: really_probe: bound device gpio-keys to driver gpio-keys
bus: ‘platform‘: add driver s3c-keypad
bus: ‘platform‘: driver_probe_device: matched device s3c-keypad with driver s3c-keypad
bus: ‘platform‘: really_probe: probing driver s3c-keypad with device s3c-keypad
@@@@@@@@@@@@@ keypad size = 10
device: ‘input1‘: device_add
input: s3c-keypad as /devices/platform/s3c-keypad/input/input1
device: ‘event1‘: device_add
driver: ‘s3c-keypad‘: driver_bound: bound to device ‘s3c-keypad‘
bus: ‘platform‘: really_probe: bound device s3c-keypad to driver s3c-keypad
S3C Touchscreen driver, (c) 2008 Samsung Electronics
bus: ‘platform‘: add driver s3c-ts
bus: ‘platform‘: driver_probe_device: matched device s3c-ts with driver s3c-ts
bus: ‘platform‘: really_probe: probing driver s3c-ts with device s3c-ts
S3C TouchScreen got loaded successfully : 12 bits
device: ‘input2‘: device_add
input: S3C TouchScreen as /devices/virtual/input/input2
device: ‘mouse0‘: device_add
device: ‘event2‘: device_add
driver: ‘s3c-ts‘: driver_bound: bound to device ‘s3c-ts‘
bus: ‘platform‘: really_probe: bound device s3c-ts to driver s3c-ts
S3C24XX RTC, (c) 2004,2006 Simtec Electronics
bus: ‘platform‘: add driver s3c-rtc
bus: ‘platform‘: driver_probe_device: matched device s3c64xx-rtc with driver s3c-rtc
bus: ‘platform‘: really_probe: probing driver s3c-rtc with device s3c64xx-rtc
s3c-rtc s3c64xx-rtc: rtc disabled, re-enabling
device: ‘rtc0‘: device_add
s3c-rtc s3c64xx-rtc: rtc core: registered s3c as rtc0
driver: ‘s3c64xx-rtc‘: driver_bound: bound to device ‘s3c-rtc‘
bus: ‘platform‘: really_probe: bound device s3c64xx-rtc to driver s3c-rtc
i2c /dev entries driver
device class ‘i2c-dev‘: registering
device: ‘i2c-0‘: device_add
Linux video capture interface: v2.00
device class ‘video4linux‘: registering
gspca: main v2.10.0 registered
bus: ‘usb‘: add driver benq
usbcore: registered new interface driver benq
benq: registered
bus: ‘usb‘: add driver conex
usbcore: registered new interface driver conex
conex: registered
bus: ‘usb‘: add driver cpia1
usbcore: registered new interface driver cpia1
cpia1: registered
bus: ‘usb‘: add driver etoms
usbcore: registered new interface driver etoms
etoms: registered
bus: ‘usb‘: add driver finepix
usbcore: registered new interface driver finepix
finepix: registered
bus: ‘usb‘: add driver jeilinj
usbcore: registered new interface driver jeilinj
jeilinj: registered
bus: ‘usb‘: add driver mars
usbcore: registered new interface driver mars
mars: registered
bus: ‘usb‘: add driver mr97310a
usbcore: registered new interface driver mr97310a
mr97310a: registered
bus: ‘usb‘: add driver ov519
usbcore: registered new interface driver ov519
ov519: registered
bus: ‘usb‘: add driver ov534
usbcore: registered new interface driver ov534
ov534: registered
bus: ‘usb‘: add driver ov534_9
usbcore: registered new interface driver ov534_9
ov534_9: registered
bus: ‘usb‘: add driver pac207
usbcore: registered new interface driver pac207
pac207: registered
bus: ‘usb‘: add driver pac7302
usbcore: registered new interface driver pac7302
pac7302: registered
bus: ‘usb‘: add driver pac7311
usbcore: registered new interface driver pac7311
pac7311: registered
bus: ‘usb‘: add driver sn9c2028
usbcore: registered new interface driver sn9c2028
sn9c2028: registered
bus: ‘usb‘: add driver sn9c20x
usbcore: registered new interface driver sn9c20x
sn9c20x: registered
bus: ‘usb‘: add driver sonixb
usbcore: registered new interface driver sonixb
sonixb: registered
bus: ‘usb‘: add driver sonixj
usbcore: registered new interface driver sonixj
sonixj: registered
bus: ‘usb‘: add driver spca500
usbcore: registered new interface driver spca500
spca500: registered
bus: ‘usb‘: add driver spca501
usbcore: registered new interface driver spca501
spca501: registered
bus: ‘usb‘: add driver spca505
usbcore: registered new interface driver spca505
spca505: registered
bus: ‘usb‘: add driver spca506
usbcore: registered new interface driver spca506
spca506: registered
bus: ‘usb‘: add driver spca508
usbcore: registered new interface driver spca508
spca508: registered
bus: ‘usb‘: add driver spca561
usbcore: registered new interface driver spca561
spca561: registered
bus: ‘usb‘: add driver spca1528
usbcore: registered new interface driver spca1528
spca1528: registered
bus: ‘usb‘: add driver sq905
usbcore: registered new interface driver sq905
sq905: registered
bus: ‘usb‘: add driver sq905c
usbcore: registered new interface driver sq905c
sq905c: registered
bus: ‘usb‘: add driver sq930x
usbcore: registered new interface driver sq930x
sq930x: registered
bus: ‘usb‘: add driver sunplus
usbcore: registered new interface driver sunplus
sunplus: registered
bus: ‘usb‘: add driver stk014
usbcore: registered new interface driver stk014
stk014: registered
bus: ‘usb‘: add driver stv0680
usbcore: registered new interface driver stv0680
stv0680: registered
bus: ‘usb‘: add driver t613
usbcore: registered new interface driver t613
t613: registered
bus: ‘usb‘: add driver tv8532
usbcore: registered new interface driver tv8532
tv8532: registered
bus: ‘usb‘: add driver vc032x
usbcore: registered new interface driver vc032x
vc032x: registered
bus: ‘usb‘: add driver zc3xx
usbcore: registered new interface driver zc3xx
zc3xx: registered
bus: ‘usb‘: add driver ALi m5602
usbcore: registered new interface driver ALi m5602
ALi m5602: registered
bus: ‘usb‘: add driver STV06xx
usbcore: registered new interface driver STV06xx
STV06xx: registered
gspca_gl860: driver startup - version 0.9d10
bus: ‘usb‘: add driver gspca_gl860
usbcore: registered new interface driver gspca_gl860
gspca_gl860: driver registered
bus: ‘platform‘: add driver s3c-fimc
bus: ‘platform‘: driver_probe_device: matched device s3c-fimc.0 with driver s3c-fimc
bus: ‘platform‘: really_probe: probing driver s3c-fimc with device s3c-fimc.0
[CAM]s3c_fimc_register_controller.id=0
s3c_fimc_init_global s3c_fimc.cam_clock=-1065304896
device: ‘video0‘: device_add
s3c-fimc: controller 0 registered successfully
driver: ‘s3c-fimc.0‘: driver_bound: bound to device ‘s3c-fimc‘
bus: ‘platform‘: really_probe: bound device s3c-fimc.0 to driver s3c-fimc
bus: ‘platform‘: driver_probe_device: matched device s3c-fimc.1 with driver s3c-fimc
bus: ‘platform‘: really_probe: probing driver s3c-fimc with device s3c-fimc.1
[CAM]s3c_fimc_register_controller.id=1
device: ‘video1‘: device_add
s3c-fimc: controller 1 registered successfully
driver: ‘s3c-fimc.1‘: driver_bound: bound to device ‘s3c-fimc‘
bus: ‘platform‘: really_probe: bound device s3c-fimc.1 to driver s3c-fimc
s3c-fimc: info ov965x_init
bus: ‘i2c‘: add driver ov965x
bus: ‘i2c‘: driver_probe_device: matched device 0-0030 with driver ov965x
bus: ‘i2c‘: really_probe: probing driver ov965x with device 0-0030
[CAM]s3c_fimc_register_camera,cam->id=0
s3c_fimc.cam_clock = c080bcc0
parent clock for camera: 266.000 MHz, divisor: 11
[CAM]RESET CAM.[CAM]Reset and init reg!1cam->client=cc460c00
[CAM]Reset and init reg!1
[CAM]Reset and init reg!2
[CAM]s3c_fimc_init_camera[CAM]I2C_CAM_INIT.
[CAM]s3c_fimc_init_camera[CAM]s3c_fimc_init_camera[CAM]Reset and init reg!3
driver: ‘0-0030‘: driver_bound: bound to device ‘ov965x‘
bus: ‘i2c‘: really_probe: bound device 0-0030 to driver ov965x
S3C6400 MFC Driver, (c) 2007 Samsung Electronics
bus: ‘platform‘: add driver s3c-mfc
bus: ‘platform‘: driver_probe_device: matched device s3c-mfc with driver s3c-mfc
bus: ‘platform‘: really_probe: probing driver s3c-mfc with device s3c-mfc
->################### s3cmfc:s3c_mfc_sfr_base_virt_addr:d082e000
cym s3c_mfc_mememap: addr:5daf9000 size:1138688
device: ‘s3c-mfc‘: device_add
driver: ‘s3c-mfc‘: driver_bound: bound to device ‘s3c-mfc‘
bus: ‘platform‘: really_probe: bound device s3c-mfc to driver s3c-mfc
S3C6400 MFC Driver, (c) 2007 Samsung Electronics
S3C PostProcessor Driver v3.12, (c) 2009 Samsung Electronics
bus: ‘platform‘: add driver s3c-pp
bus: ‘platform‘: driver_probe_device: matched device s3c-pp with driver s3c-pp
bus: ‘platform‘: really_probe: probing driver s3c-pp with device s3c-pp
device: ‘s3c-pp‘: device_add
driver: ‘s3c-pp‘: driver_bound: bound to device ‘s3c-pp‘
bus: ‘platform‘: really_probe: bound device s3c-pp to driver s3c-pp
S3C6410 TV encoder Driver, (c) 2008 Samsung Electronics
bus: ‘platform‘: add driver s3c-tvenc
bus: ‘platform‘: driver_probe_device: matched device s3c-tvenc with driver s3c-tvenc
bus: ‘platform‘: really_probe: probing driver s3c-tvenc with device s3c-tvenc
device: ‘video14‘: device_add
driver: ‘s3c-tvenc‘: driver_bound: bound to device ‘s3c-tvenc‘
bus: ‘platform‘: really_probe: bound device s3c-tvenc to driver s3c-tvenc
S3C6410 TV encoder Driver init OK.
S3C6410 TV scaler Driver, (c) 2008 Samsung Electronics
bus: ‘platform‘: add driver s3c-tvscaler
bus: ‘platform‘: driver_probe_device: matched device s3c-tvscaler with driver s3c-tvscaler
bus: ‘platform‘: really_probe: probing driver s3c-tvscaler with device s3c-tvscaler
driver: ‘s3c-tvscaler‘: driver_bound: bound to device ‘s3c-tvscaler‘
bus: ‘platform‘: really_probe: bound device s3c-tvscaler to driver s3c-tvscaler
S3C6410 TV scaler Driver init OK.
S3C Rotator Driver, (c) 2008 Samsung Electronics
bus: ‘platform‘: add driver s3c-rotator
bus: ‘platform‘: driver_probe_device: matched device s3c-rotator with driver s3c-rotator
bus: ‘platform‘: really_probe: probing driver s3c-rotator with device s3c-rotator
s3c_rotator_probe called
device: ‘s3c-rotator‘: device_add
s3c_rotator_probe success
driver: ‘s3c-rotator‘: driver_bound: bound to device ‘s3c-rotator‘
bus: ‘platform‘: really_probe: bound device s3c-rotator to driver s3c-rotator
S3C JPEG Driver, (c) 2007 Samsung Electronics
bus: ‘platform‘: add driver s3c-jpeg
bus: ‘platform‘: driver_probe_device: matched device s3c-jpeg with driver s3c-jpeg
bus: ‘platform‘: really_probe: probing driver s3c-jpeg with device s3c-jpeg
[JPEG_DRV: TRACE] s3c_jpeg_probe: JPG_Init
phy_addr = 78800000..mem_size = 1034
phy_addr = 5d2f9000..mem_size = 79e000
device: ‘s3c-jpg‘: device_add
driver: ‘s3c-jpeg‘: driver_bound: bound to device ‘s3c-jpeg‘
bus: ‘platform‘: really_probe: bound device s3c-jpeg to driver s3c-jpeg
bus: ‘platform‘: add driver s3c-g2d
bus: ‘platform‘: driver_probe_device: matched device s3c-g2d with driver s3c-g2d
bus: ‘platform‘: really_probe: probing driver s3c-g2d with device s3c-g2d
s3c_g2d_probe called
device: ‘s3c-g2d‘: device_add
s3c_g2d_probe Success
driver: ‘s3c-g2d‘: driver_bound: bound to device ‘s3c-g2d‘
bus: ‘platform‘: really_probe: bound device s3c-g2d to driver s3c-g2d
S3C G2D Init : Done
S3C G3D Driver, (c) 2007-2009 Samsung Electronics
bus: ‘platform‘: add driver s3c-g3d
bus: ‘platform‘: driver_probe_device: matched device s3c-g3d with driver s3c-g3d
bus: ‘platform‘: really_probe: probing driver s3c-g3d with device s3c-g3d
device: ‘s3c-g3d‘: device_add
s3c_g3d version : 0x1050000
driver: ‘s3c-g3d‘: driver_bound: bound to device ‘s3c-g3d‘
bus: ‘platform‘: really_probe: bound device s3c-g3d to driver s3c-g3d
S3C G3D Init : Done
S3C CMM Driver, (c) 2008 Samsung Electronics
device: ‘s3c-cmm‘: device_add
bus: ‘usb‘: add driver uvcvideo
usbcore: registered new interface driver uvcvideo
USB Video Class driver (v0.1.0)
S3C2410 Watchdog Timer, (c) 2004 Simtec Electronics
bus: ‘platform‘: add driver s3c2410-wdt
bus: ‘platform‘: driver_probe_device: matched device s3c2410-wdt with driver s3c2410-wdt
bus: ‘platform‘: really_probe: probing driver s3c2410-wdt with device s3c2410-wdt
device: ‘watchdog‘: device_add
s3c2410-wdt s3c2410-wdt: watchdog inactive, reset disabled, irq enabled
driver: ‘s3c2410-wdt‘: driver_bound: bound to device ‘s3c2410-wdt‘
bus: ‘platform‘: really_probe: bound device s3c2410-wdt to driver s3c2410-wdt
Bluetooth: Virtual HCI driver ver 1.3
device: ‘vhci‘: device_add
Bluetooth: HCI UART driver ver 2.2
Bluetooth: HCI H4 protocol initialized
Bluetooth: HCI BCSP protocol initialized
Bluetooth: HCILL protocol initialized
Bluetooth: HCIATH3K protocol initialized
Bluetooth: Broadcom Blutonium firmware driver ver 1.2
bus: ‘usb‘: add driver bcm203x
usbcore: registered new interface driver bcm203x
Bluetooth: Digianswer Bluetooth USB driver ver 0.10
bus: ‘usb‘: add driver bpa10x
usbcore: registered new interface driver bpa10x
Bluetooth: BlueFRITZ! USB driver ver 1.2
bus: ‘usb‘: add driver bfusb
usbcore: registered new interface driver bfusb
Bluetooth: Generic Bluetooth USB driver ver 0.6
bus: ‘usb‘: add driver btusb
usbcore: registered new interface driver btusb
Bluetooth: Generic Bluetooth SDIO driver ver 0.1
bus: ‘sdio‘: add driver btsdio
Bluetooth: Atheros AR30xx firmware driver ver 1.0
bus: ‘usb‘: add driver ath3k
usbcore: registered new interface driver ath3k
bus: ‘sdio‘: add driver btmrvl_sdio
bus: ‘mmc‘: add driver mmcblk
sdhci: Secure Digital Host Controller Interface driver
sdhci: Copyright(c) Pierre Ossman
bus: ‘platform‘: add driver s3c-sdhci
bus: ‘platform‘: driver_probe_device: matched device s3c-sdhci.0 with driver s3c-sdhci
bus: ‘platform‘: really_probe: probing driver s3c-sdhci with device s3c-sdhci.0
s3c-sdhci s3c-sdhci.0: clock source 0: hsmmc (133000000 Hz)
s3c-sdhci s3c-sdhci.0: clock source 1: hsmmc (133000000 Hz)
s3c-sdhci s3c-sdhci.0: clock source 2: mmc_bus (24000000 Hz)
device: ‘mmc0::‘: device_add
Registered led device: mmc0::
device: ‘mmc0‘: device_add
mmc0: SDHCI controller on samsung-hsmmc [s3c-sdhci.0] using ADMA
driver: ‘s3c-sdhci.0‘: driver_bound: bound to device ‘s3c-sdhci‘
bus: ‘platform‘: really_probe: bound device s3c-sdhci.0 to driver s3c-sdhci
bus: ‘platform‘: driver_probe_device: matched device s3c-sdhci.1 with driver s3c-sdhci
bus: ‘platform‘: really_probe: probing driver s3c-sdhci with device s3c-sdhci.1
s3c-sdhci s3c-sdhci.1: clock source 0: hsmmc (133000000 Hz)
s3c-sdhci s3c-sdhci.1: clock source 1: hsmmc (133000000 Hz)
s3c-sdhci s3c-sdhci.1: clock source 2: mmc_bus (24000000 Hz)
device: ‘mmc1::‘: device_add
Registered led device: mmc1::
device: ‘mmc1‘: device_add
mmc1: SDHCI controller on samsung-hsmmc [s3c-sdhci.1] using ADMA
driver: ‘s3c-sdhci.1‘: driver_bound: bound to device ‘s3c-sdhci‘
bus: ‘platform‘: really_probe: bound device s3c-sdhci.1 to driver s3c-sdhci
bus: ‘hid‘: registered
bus: ‘hid‘: add driver a4tech
bus: ‘hid‘: add driver apple
bus: ‘hid‘: add driver belkin
bus: ‘hid‘: add driver cherry
bus: ‘hid‘: add driver chicony
bus: ‘hid‘: add driver cypress
bus: ‘hid‘: add driver ezkey
bus: ‘hid‘: add driver kensington
bus: ‘hid‘: add driver kye
bus: ‘hid‘: add driver logitech
bus: ‘hid‘: add driver microsoft
bus: ‘hid‘: add driver monterey
bus: ‘hid‘: add driver generic-usb
bus: ‘usb‘: add driver usbhid
usbcore: registered new interface driver usbhid
usbhid: USB HID core driver
device: ‘timer‘: device_add
device: ‘seq‘: device_add
bus: ‘platform‘: add driver soc-audio
bus: ‘platform‘: add driver wm9713-codec
bus: ‘platform‘: add driver samsung-audio
bus: ‘platform‘: driver_probe_device: matched device samsung-audio with driver samsung-audio
bus: ‘platform‘: really_probe: probing driver samsung-audio with device samsung-audio
driver: ‘samsung-audio‘: driver_bound: bound to device ‘samsung-audio‘
bus: ‘platform‘: really_probe: bound device samsung-audio to driver samsung-audio
bus: ‘platform‘: add driver samsung-ac97
bus: ‘platform‘: driver_probe_device: matched device samsung-ac97 with driver samsung-ac97
bus: ‘platform‘: really_probe: probing driver samsung-ac97 with device samsung-ac97
driver: ‘samsung-ac97‘: driver_bound: bound to device ‘samsung-ac97‘
bus: ‘platform‘: really_probe: bound device samsung-ac97 to driver samsung-ac97
Registering platform device ‘wm9713-codec‘. Parent at platform
device: ‘wm9713-codec‘: device_add
bus: ‘platform‘: add device wm9713-codec
bus: ‘platform‘: driver_probe_device: matched device wm9713-codec with driver wm9713-codec
bus: ‘platform‘: really_probe: probing driver wm9713-codec with device wm9713-codec
driver: ‘wm9713-codec‘: driver_bound: bound to device ‘wm9713-codec‘
bus: ‘platform‘: really_probe: bound device wm9713-codec to driver wm9713-codec
Registering platform device ‘soc-audio‘. Parent at platform
device: ‘soc-audio‘: device_add
bus: ‘platform‘: add device soc-audio
bus: ‘platform‘: driver_probe_device: matched device soc-audio with driver soc-audio
bus: ‘platform‘: really_probe: probing driver soc-audio with device soc-audio
device: ‘AC97‘: device_add
asoc: wm9713-hifi <-> samsung-ac97 mapping ok
device: ‘card0‘: device_add
device: ‘pcmC0D0p‘: device_add
device: ‘pcmC0D0c‘: device_add
device: ‘dsp‘: device_add
device: ‘audio‘: device_add
device: ‘controlC0‘: device_add
device: ‘mixer‘: device_add
device: ‘0-0:wm9713-codec‘: device_add
bus: ‘ac97‘: add device 0-0:wm9713-codec
driver: ‘soc-audio‘: driver_bound: bound to device ‘soc-audio‘
bus: ‘platform‘: really_probe: bound device soc-audio to driver soc-audio
ALSA device list:
#0: smdk6410
Netfilter messages via NETLINK v0.30.
nf_conntrack version 0.5.0 (3071 buckets, 12284 max)
ctnetlink v0.93: registering with nfnetlink.
ip_tables: (C) 2000-2006 Netfilter Core Team
TCP cubic registered
NET: Registered protocol family 17
can: controller area network core (rev 20090105 abi 8)
NET: Registered protocol family 29
can: raw protocol (rev 20090105)
can: broadcast manager protocol (rev 20090105 t)
Bluetooth: RFCOMM TTY layer initialized
Bluetooth: RFCOMM socket layer initialized
Bluetooth: RFCOMM ver 1.11
Bluetooth: BNEP (Ethernet Emulation) ver 1.3
Bluetooth: BNEP filters: protocol multicast
Bluetooth: HIDP (Human Interface Emulation) ver 1.2
bus: ‘hid‘: add driver generic-bluetooth
lib80211: common routines for IEEE802.11 drivers
lib80211_crypt: registered algorithm ‘NULL‘
lib80211_crypt: registered algorithm ‘WEP‘
lib80211_crypt: registered algorithm ‘CCMP‘
lib80211_crypt: registered algorithm ‘TKIP‘
bus: ‘platform‘: add driver rfkill_gpio
Registering the dns_resolver key type
device: ‘cpu_dma_latency‘: device_add
device: ‘network_latency‘: device_add
device: ‘network_throughput‘: device_add
s3c-rtc s3c64xx-rtc: setting system clock to 2015-05-14 10:58:30 UTC (1431601110)
yaffs: dev is 32505858 name is "mtdblock2" rw
yaffs: passed flags ""
yaffs: yaffs: Attempting MTD mount of 31.2,"mtdblock2"
yaffs: yaffs_read_super: is_checkpointed 0
VFS: Mounted root (yaffs2 filesystem) on device 31:2.
devtmpfs: mounted
Freeing init memory: 184K
yaffs: dev is 32505859 name is "mtdblock3" rw
yaffs: passed flags ""
yaffs: yaffs: Attempting MTD mount of 31.3,"mtdblock3"
yaffs: yaffs_read_super: is_checkpointed 0
Try to bring eth0 interface up......[dm9000 Ethernet Driver, V2.6.31]: Link-Down!!
dm9000 dm9000.0: eth0: link down
dm9000 dm9000.0: eth0: link down
Done
Starting Qtopia2, please waiting...
device: ‘vcs4‘: device_add
device: ‘vcsa4‘: device_add
Please press Enter to activate this console. device: ‘vcs3‘: device_add
device: ‘vcsa3‘: device_add
device: ‘vcs2‘: device_add
device: ‘vcsa2‘: device_add
touch...
时间： 2024-10-29 10:46:33