dialogic d300语音卡驱动重装后启动报错问题解决方法

dialogic d300 驱动重装后 dlstart  报错解决

问题描述:dlstart  后如下报错

[[email protected] data]#dlstop

Stopping Dialogic Services...

Stopping Clocking Daemon:[  纭畾  ]

Stopping ClockingServer:[  纭畾  ]

Stopping Telephony System Monitor:[  纭畾  ]

Stopping Dialogic(R) board(s).

Deleting SW devices ....

Deleting SW devices Done

genload[17226]: Warning - Insufficient power overriden for the PCI Express board at bus 7, slot 0.

Stopping Timeslot Doler:[  纭畾  ]

Stopping Device Mapper:[  纭畾  ]

Shutting Down OAM Event Service:[  纭畾  ]

Stopping Dialogic Runtime Tracing Server:[  纭畾  ]

[[email protected] ~]# dlstart

Starting Dialogic Services...

Starting Dialogic Runtime Tracing Server:[  纭畾  ]

Warning: You have chosen a Springware board to be the Primary clock master

Clock fallback will not be supported in this configuration

Starting OAM Event Service:[  纭畾  ]

Starting Device Mapper:[  纭畾  ]

Starting Timeslot Doler:[  纭畾  ]

Starting Telephony System Monitor:[  纭畾  ]

Starting Clocking Server:[  纭畾  ]

Starting Dialogic(R) board(s).

Dialogic(R) Generic Downloader Version 6.00 (Build 1)

Copyright (C) 1992-2007 Dialogic Corporation.

Using /usr/dialogic/cfg/dialogic.cfg to configure Dialogic Boards

genload[18399]: Warning - Insufficient power overriden for the PCI Express board at bus 7, slot 0.

System Download ........

Warning: Clock signals not detected on sec. lines

..............................................................................

D/300JCT-E1 (PCI ID 0) Download .. spisctr4 Firmware Version 6.70 Build 0024

1 Dialogic?Board Successfully Installed

Dialogic(R) SCSA Transmit Timeslot Assignment Program

Copyright (c) 1997-2007 Dialogic Corporation.  All rights reserved

sctsassign:The Start TS is: 0 and Total Number of TS: 60

dxxxB1 : Failed open in sctsdtdxag.c: No such file or directory

dxxxB2 : Failed open in sctsdtdxag.c: No such file or directory

dxxxB3 : Failed open in sctsdtdxag.c: No such file or directory

dxxxB4 : Failed open in sctsdtdxag.c: No such file or directory

dxxxB5 : Failed open in sctsdtdxag.c: No such file or directory

dtiB1 : Failed open in sctsdtdxag.c: No such file or directory

dxxxB6 : Failed open in sctsdtdxag.c: No such file or directory

dxxxB7 : Failed open in sctsdtdxag.c: No such file or directory

dxxxB8 : Failed open in sctsdtdxag.c: No such file or directory

Add SW Devices ....

REGVOX: #

REGVOX: # Dialogic Generic Configuration File

REGVOX: #

REGVOX: #

REGVOX: # Total number of virtual boards - 9

REGVOX: #

REGVOX:

REGVOX: #

REGVOX: # Board Type - D/300JCT-E1

REGVOX: #

REGVOX: dxxxB1    4  7000010   C         FBFE0000      2000       20        SPAN  50004

REGVOX: dxxxB2    4  7000010   C         FBFE2000      2000       20        SPAN  50005

REGVOX: dxxxB3    4  7000010   C         FBFE4000      2000       20        SPAN  50006

REGVOX: dxxxB4    4  7000010   C         FBFE6000      2000       20        SPAN  50007

REGVOX: dxxxB5    4  7000010   C         FBFE0000      2000        0        SPAN  50008

REGVOX: dtiB1    30  7000010   T         FBFE0000      2000        0        E1SPAN  50009

REGVOX: dxxxB6    4  7000010   C         FBFE2000      2000        0        SPAN  50010

REGVOX: dxxxB7    4  7000010   C         FBFE4000      2000        0        SPAN  50011

REGVOX: dxxxB8    2  7000010   C         FBFE6000      2000        0        SPAN  50012

Add SW Devices Done

Checking for unsupported Dialogic boards:

usbu[18448]: Warning - Insufficient power overriden for the PCI Express board at bus 7, slot 0.

Starting Clocking Daemon:[  纭畾  ]

Starting fault detection on all Dialogic boards:[  纭畾  ]

解决办法:

经过google,发现是因为语音卡驱动加载openib与streams有冲突

(1)关闭应用  epos用户下  grMain -t

(2)root检查是否有安装openib    rpm -qa | grep openib

(3)如果有,卸载openib     rpm -e openib

(4)检查是否卸载成功   rpm -qa | grep openib

(5)重启机器

(6)root用户下  dlstop

(7)root下    dlstart  查看是否启动成功

(8)epos下   grMain  -s -l5 -d5 -w -r 启动应用

参考文档:

Thought I would share this.  I recently ran into this issue when trying to start Dialogic on RHEL 4.  dlstart would produce the following.  Apparently version 6 and older of up2date will load an openib package which conflicts with streams.

SCREEN OUTPUT:

dxxxB1 : Failed open in sctsdtdxag.c: No such file or directory

dtiB1 : Failed open in sctsdtdxag.c: No such file or directory

dxxxB2 : Failed open in sctsdtdxag.c: No such file or directory

dxxxB3 : Failed open in sctsdtdxag.c: No such file or directory

dxxxB4 : Failed open in sctsdtdxag.c: No such file or directory

dxxxB5 : Failed open in sctsdtdxag.c: No such file or directory

dxxxB6 : Failed open in sctsdtdxag.c: No such file or directory

RTF LOG:

#Timestamp              #PID   #TID        #Module      #Client    #Label       #Message

06/23/2009 09:20:55.754  20988  3008342944 OAMSYSLOG               ErrorEx      DLGTIMESLOTDOLER - Fail to get TDMbus Attr error = 100

06/23/2009 09:20:55.755  20988  3008342944 OAMSYSLOG               ErrorEx      DLGTIMESLOTDOLER - Fail to get TDMbus Attr error = 100

06/23/2009 09:20:55.755  20988  3008342944 OAMSYSLOG               ErrorEx      DLGTIMESLOTDOLER - Fail to get TDMbus Attr error = 100

06/23/2009 09:20:56.249  21260  3086215392 spwrvoice               ERR1         dxmain                dxxxB1    ::::> dx_open() = -1, open(/dev/dlgn) = -1

06/23/2009 09:20:56.258  21260  3086215392 spwrvoice               ERR1         dxmain                dxxxB2    ::::> dx_open() = -1, open(/dev/dlgn) = -1

06/23/2009 09:20:56.259  21260  3086215392 spwrvoice               ERR1         dxmain                dxxxB3    ::::> dx_open() = -1, open(/dev/dlgn) = -1

06/23/2009 09:20:56.261  21260  3086215392 spwrvoice               ERR1         dxmain                dxxxB4    ::::> dx_open() = -1, open(/dev/dlgn) = -1

06/23/2009 09:20:56.262  21260  3086215392 spwrvoice               ERR1         dxmain                dxxxB5    ::::> dx_open() = -1, open(/dev/dlgn) = -1

06/23/2009 09:20:56.264  21260  3086215392 spwrvoice               ERR1         dxmain                dxxxB6    ::::> dx_open() = -1, open(/dev/dlgn) = -1

06/23/2009 09:20:57.375  21327  3086096896 OAMSYSLOG               ErrorEx      dlgclockdaemon - ConfigTDMBus(): Cannot retrieve TDM bus attributes from Device Mapper for bus id 158570088; 100 returned from dm_getAttributes().

06/23/2009 09:20:57.375  21327  3086096896 OAMSYSLOG               ErrorEx      dlgclockdaemon - ConfigTDMBus(): FATAL CONFIGURATION ERROR.

06/23/2009 09:20:57.375  21327  3086096896 OAMSYSLOG               ErrorEx      dlgclockdaemon - Failed to configure the TDM bus; ConfigTDMBus() returned 0x0.

06/23/2009 09:20:58.956  21352  3061984160 OAMIPC                  Warning      OAMTransport - CSocketClientTransport::SendMessage() - m_ClientReceiveSocket.ShutAndCloseSocket failed

06/23/2009 09:20:58.955  21051  2892954528 OAMSYSLOG               ErrorEx      DLGSPWRFAULTDETECTOR - CNIStatus::init(): Failed to open the DTI device dtiB1

FIND AND FIX:

[[email protected] cfg]# lsmod

Module                  Size  Used by

mercd                 281204  0

ctimod                 28916  1 mercd

streams_dvbmDriver    132616  0

streams_sctmrDriver    29104  0

streams_gpioDriver     21028  0

streams_gncfdDriver    19112  0

streams_dlgnDriver    418536  4 streams_dvbmDriver,streams_sctmrDriver,streams_gpioDriver,streams_gncfdDriver

streams               859756  5 streams_dvbmDriver,streams_sctmrDriver,streams_gpioDriver,streams_gncfdDriver,streams_dlgnDriver

parport_pc             28033  0

lp                     15661  0

parport                38153  2 parport_pc,lp

autofs4                26053  0

i2c_dev                14529  0

i2c_core               26305  1 i2c_dev

sunrpc                145061  1

ipt_REJECT             10689  1

ipt_state               5953  17

ip_conntrack           46085  1 ipt_state

iptable_filter          6977  1

ip_tables              23105  3 ipt_REJECT,ipt_state,iptable_filter

cpufreq_powersave       5953  0

ib_srp                 39005  0

ib_sdp                 61437  0

ib_ipoib               81769  0

inet_lro               13121  1 ib_ipoib

md5                     8129  1

ipv6                  244833  84 ib_ipoib

rdma_ucm               21189  0

rdma_cm                39937  2 ib_sdp,rdma_ucm

iw_cm                  13381  1 rdma_cm

ib_addr                12357  1 rdma_cm

ib_umad                21737  0

ib_ucm                 22213  0

ib_uverbs              41833  2 rdma_ucm,ib_ucm

ib_cm                  46521  4 ib_srp,ib_ipoib,rdma_cm,ib_ucm

ib_sa                  43213  4 ib_srp,ib_ipoib,rdma_cm,ib_cm

ib_mad                 39897  3 ib_umad,ib_cm,ib_sa

ib_core                66369  12 ib_srp,ib_sdp,ib_ipoib,rdma_ucm,rdma_cm,iw_cm,ib_umad,ib_ucm,ib_uverbs,ib_cm,ib_sa,ib_mad

button                 10705  0

battery                12997  0

ac                      8901  0

uhci_hcd               33241  0

e100                   36677  0

mii                     9281  1 e100

e1000                 122837  0

floppy                 58193  0

dm_snapshot            22633  0

dm_zero                 6337  0

dm_mirror              32969  0

ext3                  119753  4

jbd                    59865  1 ext3

dm_mod                 67049  12 dm_snapshot,dm_zero,dm_mirror

ata_piix               19909  2

libata                105629  1 ata_piix

sd_mod                 20801  3

scsi_mod              120525  3 ib_srp,libata,sd_mod

[[email protected] cfg]# rpm -qa | grep openib

openib-1.4-1.el4

[[email protected] cfg]# rpm -e openib

[[email protected] cfg]# rpm -qa | grep openib

Then reboot and all is back to normal.  Hope this helps some one else out there.

北京行二号机  dlstart  报错解决

问题描述:dlstart  后如下报错

[[email protected] data]#dlstop

Stopping Dialogic Services...

Stopping Clocking Daemon:[  纭畾  ]

Stopping ClockingServer:[  纭畾  ]

Stopping Telephony System Monitor:[  纭畾  ]

Stopping Dialogic(R) board(s).

Deleting SW devices ....

Deleting SW devices Done

genload[17226]: Warning - Insufficient power overriden for the PCI Express board at bus 7, slot 0.

Stopping Timeslot Doler:[  纭畾  ]

Stopping Device Mapper:[  纭畾  ]

Shutting Down OAM Event Service:[  纭畾  ]

Stopping Dialogic Runtime Tracing Server:[  纭畾  ]

[[email protected] ~]# dlstart

Starting Dialogic Services...

Starting Dialogic Runtime Tracing Server:[  纭畾  ]

Warning: You have chosen a Springware board to be the Primary clock master

Clock fallback will not be supported in this configuration

Starting OAM Event Service:[  纭畾  ]

Starting Device Mapper:[  纭畾  ]

Starting Timeslot Doler:[  纭畾  ]

Starting Telephony System Monitor:[  纭畾  ]

Starting Clocking Server:[  纭畾  ]

Starting Dialogic(R) board(s).

Dialogic(R) Generic Downloader Version 6.00 (Build 1)

Copyright (C) 1992-2007 Dialogic Corporation.

Using /usr/dialogic/cfg/dialogic.cfg to configure Dialogic Boards

genload[18399]: Warning - Insufficient power overriden for the PCI Express board at bus 7, slot 0.

System Download ........

Warning: Clock signals not detected on sec. lines

..............................................................................

D/300JCT-E1 (PCI ID 0) Download .. spisctr4 Firmware Version 6.70 Build 0024

1 Dialogic?Board Successfully Installed

Dialogic(R) SCSA Transmit Timeslot Assignment Program

Copyright (c) 1997-2007 Dialogic Corporation.  All rights reserved

sctsassign:The Start TS is: 0 and Total Number of TS: 60

dxxxB1 : Failed open in sctsdtdxag.c: No such file or directory

dxxxB2 : Failed open in sctsdtdxag.c: No such file or directory

dxxxB3 : Failed open in sctsdtdxag.c: No such file or directory

dxxxB4 : Failed open in sctsdtdxag.c: No such file or directory

dxxxB5 : Failed open in sctsdtdxag.c: No such file or directory

dtiB1 : Failed open in sctsdtdxag.c: No such file or directory

dxxxB6 : Failed open in sctsdtdxag.c: No such file or directory

dxxxB7 : Failed open in sctsdtdxag.c: No such file or directory

dxxxB8 : Failed open in sctsdtdxag.c: No such file or directory

Add SW Devices ....

REGVOX: #

REGVOX: # Dialogic Generic Configuration File

REGVOX: #

REGVOX: #

REGVOX: # Total number of virtual boards - 9

REGVOX: #

REGVOX:

REGVOX: #

REGVOX: # Board Type - D/300JCT-E1

REGVOX: #

REGVOX: dxxxB1    4  7000010   C         FBFE0000      2000       20        SPAN  50004

REGVOX: dxxxB2    4  7000010   C         FBFE2000      2000       20        SPAN  50005

REGVOX: dxxxB3    4  7000010   C         FBFE4000      2000       20        SPAN  50006

REGVOX: dxxxB4    4  7000010   C         FBFE6000      2000       20        SPAN  50007

REGVOX: dxxxB5    4  7000010   C         FBFE0000      2000        0        SPAN  50008

REGVOX: dtiB1    30  7000010   T         FBFE0000      2000        0        E1SPAN  50009

REGVOX: dxxxB6    4  7000010   C         FBFE2000      2000        0        SPAN  50010

REGVOX: dxxxB7    4  7000010   C         FBFE4000      2000        0        SPAN  50011

REGVOX: dxxxB8    2  7000010   C         FBFE6000      2000        0        SPAN  50012

Add SW Devices Done

Checking for unsupported Dialogic boards:

usbu[18448]: Warning - Insufficient power overriden for the PCI Express board at bus 7, slot 0.

Starting Clocking Daemon:[  纭畾  ]

Starting fault detection on all Dialogic boards:[  纭畾  ]

解决办法:

经过google,发现是因为语音卡驱动加载openib与streams有冲突

(1)关闭应用  epos用户下  grMain -t

(2)root检查是否有安装openib    rpm -qa | grep openib

(3)如果有,卸载openib     rpm -e openib

(4)检查是否卸载成功   rpm -qa | grep openib

(5)重启机器

(6)root用户下  dlstop

(7)root下    dlstart  查看是否启动成功

(8)epos下   grMain  -s -l5 -d5 -w -r 启动应用

感谢这位国外的和我一样的倒霉蛋。

参考文档:

Thought I would share this.  I recently ran into this issue when trying to start Dialogic on RHEL 4.  dlstart would produce the following.  Apparently version 6 and older of up2date will load an openib package which conflicts with streams.

SCREEN OUTPUT:

dxxxB1 : Failed open in sctsdtdxag.c: No such file or directory

dtiB1 : Failed open in sctsdtdxag.c: No such file or directory

dxxxB2 : Failed open in sctsdtdxag.c: No such file or directory

dxxxB3 : Failed open in sctsdtdxag.c: No such file or directory

dxxxB4 : Failed open in sctsdtdxag.c: No such file or directory

dxxxB5 : Failed open in sctsdtdxag.c: No such file or directory

dxxxB6 : Failed open in sctsdtdxag.c: No such file or directory

RTF LOG:

#Timestamp              #PID   #TID        #Module      #Client    #Label       #Message

06/23/2009 09:20:55.754  20988  3008342944 OAMSYSLOG               ErrorEx      DLGTIMESLOTDOLER - Fail to get TDMbus Attr error = 100

06/23/2009 09:20:55.755  20988  3008342944 OAMSYSLOG               ErrorEx      DLGTIMESLOTDOLER - Fail to get TDMbus Attr error = 100

06/23/2009 09:20:55.755  20988  3008342944 OAMSYSLOG               ErrorEx      DLGTIMESLOTDOLER - Fail to get TDMbus Attr error = 100

06/23/2009 09:20:56.249  21260  3086215392 spwrvoice               ERR1         dxmain                dxxxB1    ::::> dx_open() = -1, open(/dev/dlgn) = -1

06/23/2009 09:20:56.258  21260  3086215392 spwrvoice               ERR1         dxmain                dxxxB2    ::::> dx_open() = -1, open(/dev/dlgn) = -1

06/23/2009 09:20:56.259  21260  3086215392 spwrvoice               ERR1         dxmain                dxxxB3    ::::> dx_open() = -1, open(/dev/dlgn) = -1

06/23/2009 09:20:56.261  21260  3086215392 spwrvoice               ERR1         dxmain                dxxxB4    ::::> dx_open() = -1, open(/dev/dlgn) = -1

06/23/2009 09:20:56.262  21260  3086215392 spwrvoice               ERR1         dxmain                dxxxB5    ::::> dx_open() = -1, open(/dev/dlgn) = -1

06/23/2009 09:20:56.264  21260  3086215392 spwrvoice               ERR1         dxmain                dxxxB6    ::::> dx_open() = -1, open(/dev/dlgn) = -1

06/23/2009 09:20:57.375  21327  3086096896 OAMSYSLOG               ErrorEx      dlgclockdaemon - ConfigTDMBus(): Cannot retrieve TDM bus attributes from Device Mapper for bus id 158570088; 100 returned from dm_getAttributes().

06/23/2009 09:20:57.375  21327  3086096896 OAMSYSLOG               ErrorEx      dlgclockdaemon - ConfigTDMBus(): FATAL CONFIGURATION ERROR.

06/23/2009 09:20:57.375  21327  3086096896 OAMSYSLOG               ErrorEx      dlgclockdaemon - Failed to configure the TDM bus; ConfigTDMBus() returned 0x0.

06/23/2009 09:20:58.956  21352  3061984160 OAMIPC                  Warning      OAMTransport - CSocketClientTransport::SendMessage() - m_ClientReceiveSocket.ShutAndCloseSocket failed

06/23/2009 09:20:58.955  21051  2892954528 OAMSYSLOG               ErrorEx      DLGSPWRFAULTDETECTOR - CNIStatus::init(): Failed to open the DTI device dtiB1

FIND AND FIX:

[[email protected] cfg]# lsmod

Module                  Size  Used by

mercd                 281204  0

ctimod                 28916  1 mercd

streams_dvbmDriver    132616  0

streams_sctmrDriver    29104  0

streams_gpioDriver     21028  0

streams_gncfdDriver    19112  0

streams_dlgnDriver    418536  4 streams_dvbmDriver,streams_sctmrDriver,streams_gpioDriver,streams_gncfdDriver

streams               859756  5 streams_dvbmDriver,streams_sctmrDriver,streams_gpioDriver,streams_gncfdDriver,streams_dlgnDriver

parport_pc             28033  0

lp                     15661  0

parport                38153  2 parport_pc,lp

autofs4                26053  0

i2c_dev                14529  0

i2c_core               26305  1 i2c_dev

sunrpc                145061  1

ipt_REJECT             10689  1

ipt_state               5953  17

ip_conntrack           46085  1 ipt_state

iptable_filter          6977  1

ip_tables              23105  3 ipt_REJECT,ipt_state,iptable_filter

cpufreq_powersave       5953  0

ib_srp                 39005  0

ib_sdp                 61437  0

ib_ipoib               81769  0

inet_lro               13121  1 ib_ipoib

md5                     8129  1

ipv6                  244833  84 ib_ipoib

rdma_ucm               21189  0

rdma_cm                39937  2 ib_sdp,rdma_ucm

iw_cm                  13381  1 rdma_cm

ib_addr                12357  1 rdma_cm

ib_umad                21737  0

ib_ucm                 22213  0

ib_uverbs              41833  2 rdma_ucm,ib_ucm

ib_cm                  46521  4 ib_srp,ib_ipoib,rdma_cm,ib_ucm

ib_sa                  43213  4 ib_srp,ib_ipoib,rdma_cm,ib_cm

ib_mad                 39897  3 ib_umad,ib_cm,ib_sa

ib_core                66369  12 ib_srp,ib_sdp,ib_ipoib,rdma_ucm,rdma_cm,iw_cm,ib_umad,ib_ucm,ib_uverbs,ib_cm,ib_sa,ib_mad

button                 10705  0

battery                12997  0

ac                      8901  0

uhci_hcd               33241  0

e100                   36677  0

mii                     9281  1 e100

e1000                 122837  0

floppy                 58193  0

dm_snapshot            22633  0

dm_zero                 6337  0

dm_mirror              32969  0

ext3                  119753  4

jbd                    59865  1 ext3

dm_mod                 67049  12 dm_snapshot,dm_zero,dm_mirror

ata_piix               19909  2

libata                105629  1 ata_piix

sd_mod                 20801  3

scsi_mod              120525  3 ib_srp,libata,sd_mod

[[email protected] cfg]# rpm -qa | grep openib

openib-1.4-1.el4

[[email protected] cfg]# rpm -e openib

[[email protected] cfg]# rpm -qa | grep openib

Then reboot and all is back to normal.  Hope this helps some one else out there.

时间: 2024-10-08 10:08:51

dialogic d300语音卡驱动重装后启动报错问题解决方法的相关文章

初次安装hive-2.1.0启动报错问题解决方法

首次安装hive-2.1.0,通过bin/hive登录hive shell命令行,报错如下: [[email protected] hive-2.1.0]$ bin/hive which: no hbase in (/opt/service/jdk1.7.0_67/bin:/opt/service/jdk1.7.0_67/jre/bin:/opt/mysql-5.6.24/bin:/opt/service/jdk1.7.0_67/bin:/opt/service/jdk1.7.0_67/jre/

安装mongodb后启动报错libstdc++

安装mongo后启动报错如下图 显然说是libstdc++.so文件版本的问题,这种一般都是gcc版本太低了 接着查询gcc的版本    strings /usr/lib/libstdc++.so.6 | grep GLIBCXX 接着去找下libstdc++.so新点的版本,一定要根据自己的系统版本去找啊,由于我找错了版本报错系统位数不对 随后下载了一个64位的libstdc++.so.6.0.17的文件,然后软链成libstdc++.so.6 ln -s libstdc++.so.6.0.1

kafka启动报错&问题解决

kafka启动报错&问题解决 一早上班,就收到运维同事通知说有一台物理机宕机,导致虚拟机挂了.只得重启kafka服务器. 1.启动 启动zookeeper bin/zkServer.sh start conf/zoo.cfg & 启动kafka bin/kafka-server-start.sh config/server.properties & 2.测试 问题一 kafka启动之后,发现一直打印warn,上图.且在进程中ps -ef| grep kafka,无法看到.很明显ka

mysql故障:重启mysql后启动报错

昨天在试运行环境做系统升级,突然间SSH连接断开,尝试进行连接一直报错,后来重启我的电脑再次进行连接,依然报错,奇怪的测试人员访问公司的liferay界面可以正常访问,后来给部门同事打电话问他们今天有没有对试运行环境做过什么修改,两个同事都说是今天没有对试运行服务器做过任何操作,我自己也没有做过什么操作,后来跟机房的技术支持打电话咨询了一下,技术支持说机房今天也没有做什么操作更没有做什么限制,后来通过登录Xenserver来登录到试运行这台机器,发现没有异常,还特意看了一下SSH的连接数,查看l

centos7 安装docker后启动报错

启动docker $ sudo systemctl start docker 报错. 查看状态: $ systemctl status docker.service -l 加 -l 有的行信息很长,打印的时候会省略,加此参数则全部显示. 报错信息: Error starting daemon: SELinux is not supported with the overlay2 graph driver on this kernel. Either boot into a newer kerne

maven引入dubbo包后启动报错

启动后报错内容为: Caused by: org.springframework.beans.factory.BeanDefinitionStoreException: Unexpected exception parsing XML document from URL [config/spring-context.xml]; nested exception is java.lang.IllegalStateException: Context namespace element 'compo

ipvsadm启动报错解决方法

Centos7 yum -y install ipvadm 安装后,启动ipvsadm却报错. Redirecting to /bin/systemctl start ipvsadm.service Job for ipvsadm.service failed because the control process exited with error code. See "systemctl status ipvsadm.service" and "journalctl -x

Redis 5.0.3默认配置启动报错解决方法

一.redis默认配置启动报错误信息如下 # /usr/local/redis/bin/redis-server /usr/local/src/redis-5.0.3/redis.conf 5852:C 24 Jan 2019 23:00:07.676 # oO0OoO0OoO0Oo Redis is starting oO0OoO0OoO0Oo 5852:C 24 Jan 2019 23:00:07.676 # Redis version=5.0.3, bits=64, commit=0000

dbeaver解压后启动报错Could not resolve module: org.eclipse.compare

dbeaver工具对很多数据库都支持,但目前对oracle支持的不是特别好,mysql还行吧,其他的还没怎么使用.下载dbeaver解压版后,点击dbeaver.exe刚开始是会报错误的 在对应的目录下查看日志文件中有 !MESSAGE FrameworkEvent ERROR !STACK 0 org.osgi.framework.BundleException: Could not resolve module: org.eclipse.compare [17] Unresolved req