Raspberry Pi开发之旅-空气温湿度检测（DHT11）

一、首先，简单介绍下DHT11:

DHT11是一个温湿度传感器，分为3个接口，分别为：VCC, DATA, GND

之前看网上说，需要在DHT11VCC和DATA之间加一个电阻，经试验完全不需要。

二、引脚连接：

1.VCC接上3V，可以选择1口或者17口

2.DATA接上GPIO口，我选的是GPIO4，第7口

3.GND接上接地口，我选的是第14口

三、Python获取温湿度：

#!/usr/bin/python
import RPi.GPIO as GPIO
import time

channel =4
data = []
j = 0

GPIO.setmode(GPIO.BCM)

time.sleep(1)

GPIO.setup(channel, GPIO.OUT)
GPIO.output(channel, GPIO.LOW)
time.sleep(0.02)
GPIO.output(channel, GPIO.HIGH)
GPIO.setup(channel, GPIO.IN)

while GPIO.input(channel) == GPIO.LOW:
  continue
while GPIO.input(channel) == GPIO.HIGH:
  continue

while j < 40:
  k = 0
  while GPIO.input(channel) == GPIO.LOW:
    continue
  while GPIO.input(channel) == GPIO.HIGH:
    k += 1
    if k > 100:
      break
  if k < 8:
    data.append(0)
  else:
    data.append(1)

  j += 1

print "sensor is working."
print data

humidity_bit = data[0:8]
humidity_point_bit = data[8:16]
temperature_bit = data[16:24]
temperature_point_bit = data[24:32]
check_bit = data[32:40]

humidity = 0
humidity_point = 0
temperature = 0
temperature_point = 0
check = 0

for i in range(8):
  humidity += humidity_bit[i] * 2 ** (7-i)
  humidity_point += humidity_point_bit[i] * 2 ** (7-i)
  temperature += temperature_bit[i] * 2 ** (7-i)
  temperature_point += temperature_point_bit[i] * 2 ** (7-i)
  check += check_bit[i] * 2 ** (7-i)

tmp = humidity + humidity_point + temperature + temperature_point

if check == tmp:
  print "temperature :", temperature, "*C, humidity :", humidity, "%"
else:
  print "wrong"
  print "temperature :", temperature, "*C, humidity :", humidity, "% check :", check, ", tmp :", tmp

GPIO.cleanup()

四、展示结果：

[email protected]:/data/basedata# python/dht11.py
sensor is working.
[0, 0, 1, 0, 0, 1, 1, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 1, 0, 1, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 1, 1, 1, 0, 1, 0]
temperature : 23 *C, humidity : 93 %

为了测试结果是否准确，我把手指放到传感器上，测试的数据为：

[email protected]:/data/basedata/python# python dht11.py
sensor is working.
[0, 0, 1, 0, 0, 1, 1, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 1, 0, 0, 1, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 1, 1, 0, 1, 1, 1, 1]
temperature : 36 *C, humidity : 95 %

测试无误～

PS: 如果你用的是DS18B20，需要做以下动作：

[email protected]:/# apt-get update
[email protected]:/# apt-get upgrade #更新内核
[email protected]:/# reboot
[email protected]:/# vi /boot/config.txt #在最后一行手动添加：dtoverlay=w1-gpio-pullup,gpiopin=4 来支持新系统读取w1总线设备
[email protected]:/# modprobe w1-gpio #确认设备是否生效
[email protected]:/# modprobe w1-therm
[email protected]:/# cd /sys/bus/w1/devices/