DG449 High Voltage Single SPDT Analog Switch in SOT23-8

DESCRIPTION

The DG449 is a dual supply single-pole/double-throw (SPDT) switches.

On resistance is 38 ? and flatness is 2.6 ? max over the specified analog signal range.

These analog switches were designed to provide high speed, low error switching of precision analog signals.

The primary application areas are in the routing and switching in telecommunications and test equipment.

Combining low power, low leakages, low on-resistance and small physical size,

the DG449 is also ideally suited for portable and battery powered industrial and military equipment.

The DG449 operates either from a single + 7 V to 36 V supply or from dual ± 4.5 V to ± 20 V supplies.

It is offered in the very popular, small SOT23-8 package.

时间： 2024-10-10 21:49:31

DG449 High Voltage Single SPDT Analog Switch in SOT23-8的相关文章

Voltage Translation for Analog to Digital Interface ADC

Voltage Translation for Analog to Digital Interface 孕龙逻辑分析仪 ZeroPlus Logic Analyzer In today's microcontroller market, most of the Analog to Digital converters are only able to accept voltages from the Vcc of the device to ground. But what if you wan

how to generate an analog output from a in-built pwm of Atmega 32AVR microcontrloller?

how to generate an analog output from a in-built pwm of Atmega 32AVR microcontrloller? you need a resistor, a capacitor and an opamp. opamp is not really necessary when you are driving a mosfet, but will make life a bit easier. just be aware, that th

DAC Essentials

http://e2e.ti.com/blogs_/b/analogwire/archive/tags/DAC%2bEssentials DAC Essentials: A new blog series A digital-to-analog converter, or DAC, performs the opposite function of an analog-to-digital converter, or ADC. Duh, right? But, have you ever wond

Transistor 晶体管场效应双极型达林顿 CMOS PMOS BJT FET

Transistor Tutorial Summary Transistor Tutorial Summary Bipolar Junction Transistor Tutorial We can summarise this transistors tutorial section as follows: The Bipolar Junction Transistor (BJT) is a three layer device constructed form two semiconduct

[原创]mininet安装

mininet安装: on Ubuntu 13.04: sudo apt-get install minineton Ubuntu 12.10: sudo apt-get install mininet/quantal-backportson Ubuntu 12.04: sudo apt-get install mininet/precise-backports一.安装环境: ubuntu-12.04-32bit二.安装mininet: #rm /usr/local/bin/ovs* /usr/

Device Mapper Multipath（DM-Multipath）

Device Mapper Multipath(DM-Multipath)可以将服务器节点和存储阵列之间的多条I/O链路配置为一个单独的设备.这些I/O链路是由不同的线缆.交换机.控制器组成的SAN物理链路.Multipath将这些链路聚合在一起,生成一个单独的新的设备. 1.DM-Multipath概览: (1)数据冗余 DM-Multipath可以实现在active/passive模式下的灾难转移.在active/passive模式下,只有一半的链路在工作,如果链路上的某一部分(线缆.交换机

Linux Ethernet Bonding Driver HOWTO 英文原版

Linux Ethernet Bonding Driver HOWTO Latest update: 12 November 2007 Initial release : Thomas Davis <tadavis at lbl.gov> Corrections, HA extensions : 2000/10/03-15 : - Willy Tarreau <willy at meta-x.org> - Constantine Gavrilov <const-g at xp

【MAX10评测】（五）功耗实测

MAX 10系列FPGA的电源供电配置可分为两类:单电源供电和双电源供电单电源供电器件 MAX 10单电源供电器件仅需要使用一个3.0 V或3.3 V外部电源,作为VCC_ONE(内核电压)和VCCA(PLL和ADC电压)电源管脚的输入,内核逻辑操作所需的1.2 V是由内部电压稳压器转换得到. 双电源供电器件 MAX 10双电源供电器件需要1.2 V和2.5 V以进行器件内核逻辑和外围操作,这样就无需使用FPGA内部的电压稳压器了. 这次评测的MAX 10评估套件选用的是什么类型的器件呢?其实

Mininet入门学习

常用命令: $ sudo mn --custom ~/mininet/custom/topo-2sw-2host.py --topo mytopo --test pingall # dpctl dump-flows tcp:127.0.0.1:6634 # dpctl show tcp:127.0.0.1:6634 # dpctl add-flow tcp:127.0.0.1:6634 in_port=1, actions=output:2 $ ./pox.py log.level --DEBU