Bonding is aggregation multiple links to single link in order to increase throughput and achieve redundancy in case one of links fails. At least, officials say it so it must be true. Now, let me ask the question. How can we configure bonding?
From what I know about bonding, they are two possibilities to configure it.
The first option is to load bonding module to kernel and use ifenslave utility for its configuration. Configuration steps for Microcore are described here.
If you want to have fun as I had with bonding configuration, check this lab for reference.
http://brezular.com/2011/03/10/etherchannelvrrp-dhcp-ospf-configuration-cisco-vyatta-microcore/
As the tutorial should be dedicated to bonding on Openvswitch I should focus on this topic. This is the second option how can we configure bonding without loading bonding module to Linux kernel.
Let’s say we have two Microcore Linux boxes connected with two links. As usual, our topology is created using GNS3 andQemu images of Microcore with installed Openvswitch 1.2.2 andQuagga 0.99.20 on the top of Microcore.
There is nothing in the world what could prevent you to download my Openvswitch Microcore Qemu image available here.
As for Ethernet card I suggest you to use emulated i82557b Ethernet card. Hint – check GNS3 Qemu setting. According to Bill, 640 kB is enough for anyone but it is better to assign at least 128 MB RAM for Microcore. Here is a snapshot of Qemu setting.
Part1 – Basic Microcore, Openvswitch and Quagga Configuration
Before we start to configure Openvswitch we should be aware of initial configuration requirement for Openvswitch and Quagga. Frankly to say, Openvswitch is not Cisco IOS which you can configure right after device is booted. First you need to create database, configuration files, start services etc.
My Qemu Microcore image with Openvswitch and Quaggae is preconfigured for such things so feel free to use it.
1. Switch 1 configuration – hostname, trunks, vlan interfaces
[email protected]:~$ echo "hostname Switch1" >> /opt/bootlocal.sh
[email protected]:~$ sudo hostname Switch1
[email protected]:~$ sudo su
[email protected]:~# ovs-vsctl add-br br0
[email protected]:~# ovs-vsctl add-port br0 vlan10 tag=10 -- set interface vlan10 type=internal
[email protected]:~# ovs-vsctl add-port br0 vlan20 tag=20 -- set interface vlan20 type=internal
Note: I usually specify list of VLANs to be allowed on trunk link
[email protected]:~# ovs-vsctl add-port br0 eth0 trunks=10,20
[email protected]:~# ovs-vsctl add-port br0 eth1 trunks=10,20
Unfortunately if we do it now, we cannot create bond0 interface, later in Part2. In this case a warning message informs us that eth0 and eth1 already exists on bridge br0. Therefore we skip a trunk definition here and we will configure the trunk later together with bonding configuration.
Start Quagga vtysh shell.
[email protected]:~# vtysh
Hello, this is Quagga (version 0.99.20).
Copyright 1996-2005 Kunihiro Ishiguro, et al.
Switch1# conf t
Switch1(config)# interface vlan10
Switch1(config-if)# ip address 192.168.10.1/24
Switch1(config-if)# no shutdown
Switch1(config-if)#
Switch1(config-if)# interface vlan20
Switch1(config-if)# ip address 192.168.20.1/24
Switch1(config-if)# no shutdown
Switch1(config-if)# do wr
Switch1(config-if)# exit
Switch1(config)# exit
Switch1# exit.
Save Microcore configuration.
[email protected]:~# /usr/bin/filetool.sh -b
Ctrl+S
2. Switch 2 configuration – hostname, trunks, vlan interfaces
[email protected]:~$ echo "hostname Switch2" >> /opt/bootlocal.sh
[email protected]:~$ sudo hostname Switch2
[email protected]:~$ sudo su
[email protected]:~# ovs-vsctl add-br br0
[email protected]:~# ovs-vsctl add-port br0 vlan10 tag=10 -- set interface vlan10 type=internal
[email protected]:~# ovs-vsctl add-port br0 vlan20 tag=20 -- set interface vlan20 type=internal
Start Quagga vtysh shell.
[email protected]:~# vtysh
Hello, this is Quagga (version 0.99.20).
Copyright 1996-2005 Kunihiro Ishiguro, et al.
Switch2# conf t
Switch2(config)# interface vlan10
Switch2(config-if)# ip address 192.168.10.2/24
Switch2(config-if)# no shutdown
Switch2(config-if)#
Switch2(config-if)# interface vlan20
Switch2(config-if)# ip address 192.168.20.2/24
Switch2(config-if)# no shutdown
Switch2(config-if)# do wr
Switch2(config-if)# exit
Switch2(config)# exit
Switch2# exit
[email protected]:~#
Save Microcore configuration.
[email protected]:~# /usr/bin/filetool.sh -b
Ctrl+S
Part2 – Bonding
Now, it is time to start playing game called bonding. They are not any rules in our game but it is not bad idea to read documentation first. Page number ten could answer many future question.
http://openvswitch.org/ovs-vswitchd.conf.db.5.pdf
As you can see, they are four bond modes with balance-slb as default mode. Modes are described on page 11.
1. Switch1 and Switch2 configuration for static bonding
[email protected]:~# ovs-vsctl add-bond br0 bond0 eth0 eth1 trunks=10,20
[email protected]:~# ovs-vsctl add-bond br0 bond0 eth0 eth1 trunks=10,20
2. Static Bonding Testing
Check bond interface bond0 on Switch1.
[email protected]:~# ovs-appctl bond/show bond0
bond_mode: balance-slb
bond-hash-algorithm: balance-slb
bond-hash-basis: 0
updelay: 0 ms
downdelay: 0 ms
next rebalance: 9476 ms
lacp_negotiated: false
slave eth1: enabled
may_enable: true
slave eth0: enabled
active slave
may_enable: true
Now do the same for bond0 on Switch2.
[email protected]:~# ovs-appctl bond/show bond0
bond_mode: balance-slb
bond-hash-algorithm: balance-slb
bond-hash-basis: 0
updelay: 0 ms
downdelay: 0 ms
next rebalance: 7420 ms
lacp_negotiated: false
slave eth1: enabled
may_enable: true
slave eth0: enabled
active slave
may_enable: true
Now, start pinging IP address 192.168.10.2 from Switch1. Ping is supposed to be working. While pinging, start tcpdump to listen on interface ethernet1 of Switch2
[email protected]:~# tcpdump -i eth1
tcpdump: WARNING: eth1: no IPv4 address assigned
tcpdump: verbose output suppressed, use -v or -vv for full protocol decode
listening on eth1, link-type EN10MB (Ethernet), capture size 68 bytes
11:47:07.214753 IP 192.168.10.2 > 192.168.10.1: ICMP echo reply, id 36360, seq 15, length 64
11:47:08.215483 IP 192.168.10.2 > 192.168.10.1: ICMP echo reply, id 36360, seq 16, length 64
11:47:09.215823 IP 192.168.10.2 > 192.168.10.1: ICMP echo reply, id 36360, seq 17, length 64
11:47:10.216846 IP 192.168.10.2 > 192.168.10.1: ICMP echo reply, id 36360, seq 18, length 64
11:47:11.217868 IP 192.168.10.2 > 192.168.10.1: ICMP echo reply, id 36360, seq 19, length 64
<output truncated>
15 packets captured
15 packets received by filter
0 packets dropped by kernel
Interface Ethernet1 sends icmp echo reply messages back to Switch1. As they are not any ICMP echo requests listed in the output, only the interface Ethernet0 receives these ICMP requests coming from Switch1.
My question is, what happens if we shutdown Ethernet0 on Switch2? Will be ICMP requests interrupted and possibly re-forwarded via interface Ethernet0 of Switch1? If yes, how long does it take?
[email protected]:~# ifconfig eth0 down
Check the bond interface bond0 on Switch2 again. As soon as Switch2 detects failure of its interface, Openvswitch puts slave eth0 do disabled state
[email protected]:~# ovs-appctl bond/show bond0
bond_mode: balance-slb
bond-hash-algorithm: balance-slb
bond-hash-basis: 0
updelay: 0 ms
downdelay: 0 ms
next rebalance: 7612 ms
lacp_negotiated: false
slave eth1: enabled
active slave
may_enable: true
hash 52: 0 kB load
slave eth0: disabled
may_enable: false
Switch1 cannot detect failure of far end interface Ethernet0. It continues to send ICMP requests to Switch2 via its Ethernet0 interface. Stop ping command and check bond interface bond0 on Switch1. Obviously, Ethernet0 is still enabled in bundle
[email protected]:~# ovs-appctl bond/show bond0
bond_mode: balance-slb
bond-hash-algorithm: balance-slb
bond-hash-basis: 0
updelay: 0 ms
downdelay: 0 ms
next rebalance: 4007 ms
lacp_negotiated: false
slave eth1: enabled
may_enable: true
slave eth0: enabled
active slave
may_enable: true
hash 133: 0 kB load
This behaviour we cannot tolerate. We need such as mechanism which helps to detect far end failure. Therefore LACP must be deployed in your configuration.
According to wiki, LACP works by sending frames (LACPDUs) down all links that have the protocol enabled. These are two main advantages comparing to static bonding.
1. Failover when a link fails when the peer will not see the link down. With static link aggregation the peer would continue sending traffic down the link causing it to be lost.
2. The device can confirm that the configuration at the other end can handle link aggregation. With Static link aggregation a cabling or configuration mistake could go undetected and cause undesirable network behaviour.
Uhm, it looks like exactly what we want. So do not hesitate and let’s go configure bonding with LACP.
3. Switch1 and Switch2 configuration for bonding with LACP
Delete existing bond0 port.
[email protected]:~# ovs-vsctl del-port br0 bond0
[email protected]:~# ovs-vsctl del-port br0 bond0
Create a new bond interface.
[email protected]:~# ovs-vsctl add-bond br0 bond0 eth0 eth1 lacp=active trunks=10,20
[email protected]:~# ovs-vsctl add-bond br0 bond0 eth0 eth1 lacp=active trunks=10,20
Check bonding on Switch1.
[email protected]:~# ovs-appctl bond/show bond0
bond_mode: balance-slb
bond-hash-algorithm: balance-slb
bond-hash-basis: 0
updelay: 0 ms
downdelay: 0 ms
next rebalance: 7763 ms
lacp_negotiated: true
slave eth0: disabled
may_enable: false
slave eth1: enabled
active slave
may_enable: true
Notice state of Ethernet0 interface. Remember, we shut-downed Ethernet0 on Switch2. Thanks to LACP, Ethernet0 is disabled in bundle on Switch1. It is awesome!
Note Even an interface Ethernet0 of Switch1 is disabled in bundle, it remains in up state
[email protected]:~# ifconfig eth0
eth0 Link encap:Ethernet HWaddr 00:AA:00:D8:E6:00
inet6 addr: fe80::2aa:ff:fed8:e600/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:112 errors:0 dropped:0 overruns:0 frame:0
TX packets:2030 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:36156 (35.3 KiB) TX bytes:336741 (328.8 KiB)
4. LACP bonding testing
The last point we want to test is how much time is required for transition for interface in bundle to disabled state, if far end fails. Logically it should depend how often are LACP messages exchanged between peers.
Start tcpdump listening on eth0 of Switch1. Then bring interface eth0 up on Switch2. Right after LACP messages are exchanged via eth0 between Switch1 and Switch2, Ethernet0 interface is brought to enabled state in bundle. See the output below
[email protected]:~# tcpdump -i eth0 -v
tcpdump: WARNING: eth0: no IPv4 address assigned
tcpdump: listening on eth0, link-type EN10MB (Ethernet), capture size 68 bytes
< DHCP requests>
14:00:14.555758 IP (tos 0×0, ttl 64, id 0, offset 0, flags [none], proto UDP (17), length 317) 0.0.0.0.bootpc > 255.255.255.255.bootps: BOOTP/DHCP, Request [|bootp]
<IPV6 messages coming from Switch1>
14:00:18.457096 00:aa:00:85:34:00 (oui Unknown) > 33:33:00:00:00:16 (oui Unknown), ethertype IPv6 (0x86dd), length 110:
0×0000: 6000 0000 0038 0001 0000 0000 0000 0000 `….8……….
0×0010: 0000 0000 0000 0000 ff02 0000 0000 0000 …………….
0×0020: 0000 0000 0000 0016 3a00 0502 ……..:…
14:00:18.957535 00:aa:00:85:34:00 (oui Unknown) > 33:33:ff:85:34:00 (oui Unknown), ethertype IPv6 (0x86dd), length 78:
0×0000: 6000 0000 0018 3aff 0000 0000 0000 0000 `…..:………
0×0010: 0000 0000 0000 0000 ff02 0000 0000 0000 …………….
0×0020: 0000 0001 ff85 3400 8700 1173 ……4….s
<LACP message coming from Switch1. Notice System 00:00:00:00:00:00. It means that Switch2 has not known about partner’s system yet>
14:00:19.217584 LACPv1, length: 110
Actor Information TLV (0×01), length: 20
System 00:aa:00:85:34:00 (oui Unknown), System Priority 65534, Key 5, Port 6, Port Priority 65535
State Flags [Activity, Aggregation, Default]
Partner Information TLV (0×02), length: 20
System 00:00:00:00:00:00 (oui Ethernet), System Priority 0, Key 0, Port 0, Port Priority 0
State Flags [none]
Collector Information TLV (0×03), length: 16
packet exceeded snapshot
<LACP message sent to Switch2. As Switch1 knows partner ID 00:aa:00:85:34:00 – MAC address of interface eth0 of Switch2>
14:00:19.217914 LACPv1, length: 110
Actor Information TLV (0×01), length: 20
System 00:aa:00:d8:e6:00 (oui Unknown), System Priority 65534, Key 5, Port 6, Port Priority 65535
State Flags [Activity, Aggregation, Synchronization, Collecting, Distributing]
Partner Information TLV (0×02), length: 20
System 00:aa:00:85:34:00 (oui Unknown), System Priority 65534, Key 5, Port 6, Port Priority 65535
State Flags [Activity, Aggregation, Default]
Collector Information TLV (0×03), length: 16
packet exceeded snapshot
<LACP message sent to Switch1. Now, Switch1 knows partner’s ID 00:aa:00:d8:e6:00 – MAC address of interface eth0 of Switch1>
14:00:19.220189 LACPv1, length: 110
Actor Information TLV (0×01), length: 20
System 00:aa:00:85:34:00 (oui Unknown), System Priority 65534, Key 5, Port 6, Port Priority 65535
State Flags [Activity, Aggregation, Synchronization, Collecting, Distributing]
Partner Information TLV (0×02), length: 20
System 00:aa:00:d8:e6:00 (oui Unknown), System Priority 65534, Key 5, Port 6, Port Priority 65535
State Flags [Activity, Aggregation, Synchronization, Collecting, Distributing]
Collector Information TLV (0×03), length: 16
packet exceeded snapshot
Explanation
00:aa:00:85:34:00 – MAC address of eth0 interface of Switch2
00:aa:00:d8:e6:00 – MAC address of eth0 interface of Switch1:
Nice! We can see structure of LACP messages but still do not know anything about time required for transition. It is time to check it.
Start pinging 192.168.10.2 from Switch1 and with the help of tcpdump find an interface where packets enter Switch2. In my case it is Ethernet1. Shutdown this interface and cheek the output of ping command. You see, ping is interrupted and it took approximately 50 seconds for ping to be recovered. It means that for 50 seconds interface Ethernet1 of Switch1 had been in enabled state. It is too much. It must be a way to short this time to acceptable level.
Issue the command below on Switch1. LACP statistic can be found there.
[email protected]:~# ovs-appctl lacp/show bond0
lacp: bond0
status: active negotiated
sys_id: 00:aa:00:d8:e6:00
sys_priority: 65534
aggregation key: 5
lacp_time: slow
slave: eth0: current attached
port_id: 6
port_priority: 65535
actor sys_id: 00:aa:00:d8:e6:00
actor sys_priority: 65534
actor port_id: 6
actor port_priority: 65535
actor key: 5
actor state: activity aggregation synchronized collecting distributing
partner sys_id: 00:aa:00:85:34:00
partner sys_priority: 65534
partner port_id: 6
partner port_priority: 65535
partner key: 5
partner state: activity aggregation synchronized collecting distributing
slave: eth1: current attached
port_id: 5
port_priority: 65535
actor sys_id: 00:aa:00:d8:e6:00
actor sys_priority: 65534
actor port_id: 5
actor port_priority: 65535
actor key: 5
actor state: activity aggregation synchronized collecting distributing
partner sys_id: 00:aa:00:85:34:00
partner sys_priority: 65534
partner port_id: 5
partner port_priority: 65535
partner key: 5
partner state: activity aggregation synchronized collecting distributing
Focus on lacp-time parameter which is set to slow. According to documentation it is:
The LACP timing used on this Port. Possible values are fast, slow and a positive number of milliseconds. By default slow is used. When configured to be fast LACP heartbeats are requested at a rate of once per second causing connectivity problems to be detected more quickly. In slow mode, heartbeats are requested at a rate of once every 30 seconds.
That is exactly what we need. Changing lacp_time from slow to fast should help us to detect failure of peer’s interface more quickly.
5. Switch1 and Switch2 configuration for bonding with LACP and lacp time set to fast
Delete existing bond interface bond0.
[email protected]:~# ovs-vsctl del-port br0 bond0
[email protected]:~# ovs-vsctl del-port br0 bond0
Create a new bond interface.
[email protected]:~# ovs-vsctl add-bond br0 bond0 eth0 eth1 lacp=active other_config:lacp-time=fast trunks=10,20
[email protected]:~# ovs-vsctl add-bond br0 bond0 eth0 eth1 lacp=active other_config:lacp_time=fast trunks=10,20
Save configuration.
[email protected]:~# /usr/bin/filetool.sh -b
[email protected]:~# /usr/bin/filetool.sh -b
Ctrl+S
If you want to check interval of sending LACP messages, start tcpdump on Switch2 while pinging IP address of VLAN interface of Switch2 from Switch1. Now, LACP message are sent every 1 second
[email protected]:~# tcpdump -i eth0
tcpdump: WARNING: eth0: no IPv4 address assigned
tcpdump: verbose output suppressed, use -v or -vv for full protocol decode
listening on eth0, link-type EN10MB (Ethernet), capture size 68 bytes
21:42:25.525007 LACPv1, length: 110
21:42:26.529846 LACPv1, length: 110
21:42:27.532092 LACPv1, length: 110
21:42:28.534532 LACPv1, length: 110
21:42:29.543080 LACPv1, length: 110
21:42:30.545620 LACPv1, length: 110
21:42:31.547848 LACPv1, length: 110
21:42:32.550717 LACPv1, length: 110
21:42:33.551271 LACPv1, length: 110
21:42:34.553382 LACPv1, length: 110
10 packets captured
10 packets received by filter
0 packets dropped by kernel
6. LACP bonding testing with enabled lacp_time=fast option
Start pinging 192.168.10.2 from Switch1 and find interface receiving ICMP echo requests on Switch2. In my case it is interface eth0. While pinging, shutdown this interface and check ping statistic
[email protected]:~# ping 192.168.10.2
PING 192.168.10.2 (192.168.10.2): 56 data bytes
64 bytes from 192.168.10.2: seq=0 ttl=64 time=1.810 ms
64 bytes from 192.168.10.2: seq=1 ttl=64 time=0.940 ms
64 bytes from 192.168.10.2: seq=2 ttl=64 time=1.610 ms
64 bytes from 192.168.10.2: seq=3 ttl=64 time=0.755 ms
<output truncated>
— 192.168.10.2 ping statistics —
27 packets transmitted, 24 packets received, 11% packet loss
round-trip min/avg/max = 0.755/3.378/48.484 ms
You see, three packet are lost. That is what we can call link redundancy if one of links fails.
Following commands helpful during troubleshooting.
Show MAC address table.
[email protected]:~# ovs-appctl fdb/show br0
List ports.
[email protected]:~# ovs-vsctl list port
END.
Part4 – OPENVSWITCH – Playing with Bonding on Openvswitch,布布扣,bubuko.com