centos6 网卡问题 Device eth0 does not seem to be present

virtualbox 重装后,添加原来安装好到centos系统,不能联网问题

service network restart

centos linux 出现Device eth0 does not seem to be present

1.用命令ip l发现 eth1 无eth0网卡 得到eth1的mac地址(也可以通过该文件查地址/etc/udev/rules.d/70-persistent-net.rules)

2.查/etc/sysconfig/network-scripts/ifcfg-eth0中HWADDR地址与eth1的mac地址不匹配.

3 vi /etc/sysconfig/network-scripts/ifcfg-eth0

将DEVICE=eth0改为eth1

HWADDR=上边的mac地址

service network restart

启动成功可以联网了

原文地址：https://www.cnblogs.com/venje/p/11024604.html

时间： 2024-10-10 06:41:08

centos6 网卡问题 Device eth0 does not seem to be present的相关文章

Linux_解决启动网卡失败 Device eth0 does not seem to be present

Linux_解决启动网卡失败  Device eth0 does not seem to be present 虚拟机克隆  发现service network restart 启动失败 故障现象: service network restartShutting down loopback insterface:                                                                                             

linux 网卡问题 Device eth0 does not seem to be present,delaying initialization.

Device eth0 does not seem to be present,delaying initialization. 网上搜索后才发现原因所在:原来vmware在复制了虚拟机后会自动生成一个新的网卡设备供该虚拟机使用,比如 原先的网卡是eth0,复制虚拟机后后就会增加eth1.但是由于没有生成相应的/etc/sysconfig/network-scripts /ifcfg-eth1文件,导致网络连接失败,这个应该是vmware的一个bug. 查看网卡配置文件/etc/udev/rul

克隆虚机网卡出现 Device eth0 does not seem to be present, delaying initialization 错误

错误原因    克隆的Linux系统在新的机器上运行,新服务器网卡物理地址已经改变.而/etc/udev/rules.d/70-persistent-net.rules这个文件确定了网卡和MAC地址的信息之间的绑定,克隆后的网卡的MAC已经发生了变化,所以导致系统认为网络设备不存在,网络不能正常启动.另外一个就是/etc/sysconfig/network-scripts/ifcfg-eth0里面MAC地址也是以前的旧信息.   关于/etc/udev/rules.d/70-persistent

Device eth0 does not seem to be present,delaying initialization. 虚拟机克隆后出现网卡起不来

一.故障现象: [[email protected] ~]# service network restart Shutting down loopback insterface:                                                       [   OK  ] Bringing up loopback insterface:                                                            [  

问题:Bringing up interface eth0: Device eth0 does not seem to be present,delaying initialization. [FAILED]—— 找不到网卡。

克隆虚拟机的时候或其他情况出现以下问题(命令service network restart): Bringing up interface eth0:  Device eth0 does not seem to be present,delaying initialization.                    [FAILED] 1.造成的原因: 第一次创建的时候,在文件: /etc/sysconfig/network-scripts/ifcfg-eth0 里面设定了网卡0绑定了MAC地

vbox克隆虚拟机，网卡启动报错“Device eth0 does not seem to be present”

vbox克隆虚拟机,网卡启动报错"Device eth0 does not seem to be present". 需要看下面三个地方:确保文件名,设备名,mac地址都一致. mac地址以vbox的设置页面上的为准. /proc/net/dev /etc/udev/rules.d/70-persistent-net.rules /etc/sysconfig/network-scripts 我这边的情况是: /proc/net/dev 文件里并不是eth0----eth3,而是eth4

Device eth0 does not seem to be present,delaying initialization

centos6.4安装 minimal ifconfig...没有看到eth0..然后重启网卡又报下面错误. 故障现象: service network restartShutting down loopback insterface:                                                                                                     [  OK  ]Bringing up loopback in

vmware报Device eth0 does not seem to be present, delaying initialization错误

系统环境: CentOS-6.8-X86_64 使用vmware的克隆功能后,使用新克隆的虚拟机会报Device eth0 does not seem to be present, delaying initialization这样一个错误,这是由于网卡MAC地址错误导致的问题. 解决方法: 1.删除/etc/udev/rules.d/70-persistent-net.rules文件 2.编辑/etc/sysconfig/network-scripts/ifcfg-ethX文件,删除关于MAC

CentOS Linux解决Device eth0 does not seem to be present

在VMware里克隆出来的CentOS Linux.. ifconfig...没有看到eth0..然后重启网卡又报下面错误. 故障现象: service network restartShutting down loopback insterface:                                                                                                     [  OK  ]Bringing up loo