【转】使用keepalived设置虚拟IP环境

准备

　　准备两台机器，IP地址信息如下：

host1： 192.168.56.103
host2： 192.168.56.104

　　为了测试需要，分别在两台机器上安装apache并启动httpd服务，使下面两个url均可访问：

• 　　http://192.168.56.103
• 　　http://192.168.56.104

安装keepalived

　　在两台机器上分别安装keepalived

sudo yum install -y keepalived

配置keepalived

host1上keepalived 配置

$ cat /etc/keepalived/keepalived.conf
vrrp_instance VI_1 {
    state MASTER
    interface eth2
    virtual_router_id 51
    priority 101
    advert_int 1
    authentication {
        auth_type PASS
        auth_pass 123456
    }
    virtual_ipaddress {
        192.168.56.105
    }
}

host2上keepalived 配置

$ cat /etc/keepalived/keepalived.conf
vrrp_instance VI_1 {
    state MASTER
    interface eth2
    virtual_router_id 51
    priority 100
    advert_int 1
    authentication {
        auth_type PASS
        auth_pass 123456
    }
    virtual_ipaddress {
        192.168.56.105
    }
}

启动keepalived 服务

$ sudo service keepalived start
$ sudo chkconfig keepalived on

测试

　　服务启动后，先访问下面的虚拟地址访问http服务器

http://192.168.56.105

查看IP地址信息

host1上IP地址信息

$ ip addr show eth2
3: eth2: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast state UP qlen 1000
    link/ether 08:00:27:32:83:82 brd ff:ff:ff:ff:ff:ff
    inet 192.168.56.103/24 brd 192.168.56.255 scope global eth2
    inet 192.168.56.105/32 scope global eth2
    inet6 fe80::a00:27ff:fe32:8382/64 scope link
       valid_lft forever preferred_lft forever

　　其中可以看到inet 192.168.56.105/32 scope global eth2，说明现在host1是作为虚拟IP的master来运行的。

host2上IP地址信息

$ ip addr show eth2
3: eth2: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast state UP qlen 1000
    link/ether 08:00:27:ec:90:7b brd ff:ff:ff:ff:ff:ff
    inet 192.168.56.104/24 brd 192.168.56.255 scope global eth2
    inet6 fe80::a00:27ff:feec:907b/64 scope link
       valid_lft forever preferred_lft forever

　　此时host2上ip地址信息中不包含虚拟IP"192.168.56.105"信息。

验证IP地址Failover

　　现在手动停止host1上的keepalived服务

$ sudo service keepalived stop

host1上IP地址信息

$ ip addr show eth2
3: eth2: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast state UP qlen 1000
    link/ether 08:00:27:32:83:82 brd ff:ff:ff:ff:ff:ff
    inet 192.168.56.103/24 brd 192.168.56.255 scope global eth2
    inet6 fe80::a00:27ff:fe32:8382/64 scope link
       valid_lft forever preferred_lft forever

　　此时host1上ip地址信息中不再包含虚拟IP"192.168.56.105"信息。

host2上IP地址信息

$ ip addr show eth2
3: eth2: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast state UP qlen 1000
    link/ether 08:00:27:ec:90:7b brd ff:ff:ff:ff:ff:ff
    inet 192.168.56.104/24 brd 192.168.56.255 scope global eth2
    inet 192.168.56.105/32 scope global eth2
    inet6 fe80::a00:27ff:feec:907b/64 scope link
       valid_lft forever preferred_lft forever

　　现在可以看到host2上ip地址信息中已经包含虚拟IP"192.168.56.105"信息了。

　　此时如果再把host1上的keepalived服务启动，会发现虚拟IP"192.168.56.105"又重新绑定到host1上了。

转载自《使用 keepalived 设置虚拟 IP 环境》

原文地址：https://www.cnblogs.com/codingmengmeng/p/10420575.html