LAB - CCNA Configuring Router-on-a-Stick Inter-VLAN

Topology

Addressing Table

Device	Interface	IPv4 Address	Subnet Mask	Default Gateway
R1	g0/0.10	172.17.10.1	255.255.255.0	N/A
	g0/0.30	172.17.30.1	255.255.255.0	N/A
PC1	NIC	172.17.10.10	/24	172.17.10.1
PC2	NIC	172.17.30.10	/24	172.17.30.1

Objectives:

Part 1: Test Connectivity without Inter-VLAN Routing.

Part 2: Add VLANs to a Switch

Part 3: Configure Subinterfaces

Part 4: Test Connectivity with Inter-VLAN Routing

Part 2: Add VLANs to a switch

Step 1: Create VLANs on S1.

create VLAN 10 and VLAN 30 on S1

Step2: Assign VLANs to ports.

Part 3: Configure Subintefaces

Step 1: Create the subinterface g0/0.10, and g0/0.30

set the encapsulation type to 802.1q and assign VLAN 10/VLAN 30 to the subinterface.
Refer to the Address Table and assign the correct IP address to the subinterface.

Part 4: Test Connectivity with Inter-VLAN Routing

时间： 2024-08-26 11:18:45

LAB - CCNA Configuring Router-on-a-Stick Inter-VLAN的相关文章

        CCNA实验七跨交换机间的vlan  

CCNA实验七跨交换机间的vlan 环境:Windows XP GNS3.0.7 VPCS.exe 目的:配置跨交换机间的vlan通信说明:使跨交换机间的vlan通信,必须把连接两个交换机的链路配置成trunk(中继),这样能使两台实现了vlan的设备之间创建链路时节省端口,让一条链路就能承载多个vlan. 步骤: 拓扑如下: 1.首先为SW1和SW2添加交换模块:方法:右键SW1单击"配置"---"单击"SW1"---"插槽&quo

Lab - Hot Standby Router Protocol

Topology Objective Configure inter-VLAN routing with HSRP to provide redundant, fault-tolerant routing to the internal network. Background Hot Standby Router Protocol (HSRP) is a Cisco-proprietary redundancy protocol for establishing a fault-tolerant

LAB - CCNA Configure Per-Interface Inter-VLAN Routng

Topology Addressing Table Device Interface IP address Subnet Mask Dfault Gateway R1 G0/0 192.168.20.1 255.255.255.0 N/A G0/1 192.168.10.1 255.255.255.0 N/A S1 VLAN010 192.168.10.11 255.255.255.0 192.168.10.1 S2 VLAN10 192.168.10.12 255.255.255.0 19

LAB - CCNP Configuring iBGP and eBGP Local Preference, and MED

Topology Objectives For IBGP peers to correctly exchange routing information, use the next-hop-self command with the Local-Preference and MED attributes. Ensure that the flat-rate, unlimited-use T1 link is used for sending and receiving data to and f

CCNA 学习笔记(七)--交换知识（VLAN VTP TRUNK)

前面认识到了路由的相关方面知道,现在我们又要开始交换机方面的学习,现在就从最基础的开始学习交换机的基本知识.路由主要是工作于OSI协议的三层(网络层),而交换机主要是工作于二层(数据链路层),但三层交换除外. 1.路由器与交换机的区别有那些? 答:1.从外观上面来区分:路由器上面的WAN口比交换机的多,交换机一般只有二到四个WAN口,而路由器最少会有四个WAN口,交换机lan口比较多,一般有4/8/16/24/48个. 2.路由器比交换机多一个路由功能,基于路由转发,二层的交换机MAC地址转发,

思科资料的所有资料目录

1．20140819单臂路由.pdf 2．CCNA 实验手册之Packet_Tracer使用教程.pdf 3．CCNA_Lab_Workbook_Sample_Labs(CDP,静态路由,端口安全).pdf 4．CCNA.CCNP.CCIE案例实战手册(交换部分).pdf 5．CCNA.CCNP.CCIE案例实战手册(路由部分).pdf 6．CCNA帧中继解法.pdf 7．CCNA级别的实际企业环境综合实验.ppt 10．hsrp.pkt 11．CCNA_2010年5月(23个实验)最新实验总

Packet Tracer实验

http://www.packettracernetwork.com/packettracer53labs.html CCNA labs - LAN Switching Lab 1 : Basic switch setup Lab 2 : Configuring switch interfaces Lab 3 : VLAN and VTP configuration Lab 4 : Port security Lab 5 : Troubleshooting Coming soon CCNA la

ENetwork Basic Configuration PT Practice SBA

CCNA Exploration: 网络基础知识 (版本 4.0) A few things to keep in mind while completing this activity: 1 Do not use the browser Back button or close or reload any exam windows during the exam. 2 Do not close Packet Tracer when you are done. It will close aut

Cisco PT模拟实验(21) 两层架构网络搭建的综合配置

Cisco PT模拟实验(21) 两层架构网络搭建的综合配置实验目的: 熟悉网络的二层结构模型及原理掌握路由交换的基本配置方法掌握搭建两层架构网络的常用技术实验背景: 情景:A公司企业网计划接入互联网,向 ISP申请了一条专线并拥有足够的公有IP地址,现要求搭建一个简易两层架构的企业内部网,具体构建需求如下: ①企业内网划分多个vlan ,减少广播域大小,提高网络稳定性 ②将用户网关配置在核心交换机上 ③搭建DHCP服务器,实现终端用户自动获取IP地址 ④在出口路由器上配置NAPT映射