以太网链路聚合配置1（手动模式的链路聚合）

<Huawei>

Aug 25 2015 09:26:52-08:00 Huawei %%01PHY/1/PHY(l)[0]:    GigabitEthernet0/0/1: c

hange status to up

Aug 25 2015 09:26:52-08:00 Huawei %%01IFNET/4/IF_STATE(l)[1]:Interface Vlanif1 ha

s turned into UP state.

Aug 25 2015 09:26:52-08:00 Huawei %%01PHY/1/PHY(l)[2]:    GigabitEthernet0/0/2: c

hange status to up

<Huawei>sys

Enter system view, return user view with Ctrl+Z.

[Huawei]sys s1

[s1]

Aug 25 2015 09:27:27-08:00 s1 DS/4/DATASYNC_CFGCHANGE:OID 1.3.6.1.4.1.2011.5.25.1

91.3.1 configurations have been changed. The current change number is 4, the chan

ge loop count is 0, and the maximum number of records is 4095.

[s1]int

[s1]interface gi

[s1]interface GigabitEthernet 0/0/1

[s1-GigabitEthernet0/0/1]und

[s1-GigabitEthernet0/0/1]undo ne

[s1-GigabitEthernet0/0/1]undo negotiation auto

[s1-GigabitEthernet0/0/1]

Aug 25 2015 09:28:07-08:00 s1 DS/4/DATASYNC_CFGCHANGE:OID 1.3.6.1.4.1.2011.5.25.1

91.3.1 configurations have been changed. The current change number is 5, the chan

ge loop count is 0, and the maximum number of records is 4095.

[s1-GigabitEthernet0/0/1]sp

[s1-GigabitEthernet0/0/1]speed 100

[s1-GigabitEthernet0/0/1]

Aug 25 2015 09:28:17-08:00 s1 DS/4/DATASYNC_CFGCHANGE:OID 1.3.6.1.4.1.2011.5.25.1

91.3.1 configurations have been changed. The current change number is 6, the chan

ge loop count is 0, and the maximum number of records is 4095.du

^

Error:Incomplete command found at ‘^‘ position.

[s1-GigabitEthernet0/0/1]dup

^

Error:Incomplete command found at ‘^‘ position.

[s1-GigabitEthernet0/0/1]du

[s1-GigabitEthernet0/0/1]duplex fu

[s1-GigabitEthernet0/0/1]duplex full

[s1-GigabitEthernet0/0/1]q

[s1]int

[s1]interface gi

[s1]interface GigabitEthernet 0/0

Aug 25 2015 09:28:37-08:00 s1 DS/4/DATASYNC_CFGCHANGE:OID 1.3.6.1.4.1.2011.5.25.1

91.3.1 configurations have been changed. The current change number is 7, the chan

ge loop count is 0, and the maximum number of records is 4095./

^

Error: Wrong parameter found at ‘^‘ position.

[s1]interface GigabitEthernet 0/0/2

[s1-GigabitEthernet0/0/2]und

[s1-GigabitEthernet0/0/2]undo ne

[s1-GigabitEthernet0/0/2]undo negotiation au

[s1-GigabitEthernet0/0/2]undo negotiation auto

[s1-GigabitEthernet0/0/2]sp

[s1-GigabitEthernet0/0/2]speed 100

[s1-GigabitEthernet0/0/2]

Aug 25 2015 09:28:57-08:00 s1 DS/4/DATASYNC_CFGCHANGE:OID 1.3.6.1.4.1.2011.5.25.1

91.3.1 configurations have been changed. The current change number is 9, the chan

ge loop count is 0, and the maximum number of records is 4095.

[s1-GigabitEthernet0/0/2]du

[s1-GigabitEthernet0/0/2]duplex fu

[s1-GigabitEthernet0/0/2]duplex full

[s1-GigabitEthernet0/0/2]q

[s1]dis

[s1]display

Aug 25 2015 09:29:07-08:00 s1 DS/4/DATASYNC_CFGCHANGE:OID 1.3.6.1.4.1.2011.5.25.1

91.3.1 configurations have been changed. The current change number is 10, the cha

nge loop count is 0, and the maximum number of records is 4095.

^

Error:Incomplete command found at ‘^‘ position.

[s1]ds

[s1]dis

[s1]display cu

[s1]display current-configuration

#

sysname s1

#

cluster enable

ntdp enable

ndp enable

#

drop illegal-mac alarm

#

diffserv domain default

#

drop-profile default

#

aaa

authentication-scheme default

authorization-scheme default

accounting-scheme default

domain default

domain default_admin

local-user admin password simple admin

local-user admin service-type http

#

interface Vlanif1

#

interface MEth0/0/1

#

interface GigabitEthernet0/0/1

undo negotiation auto

speed 100

#

interface GigabitEthernet0/0/2

undo negotiation auto

speed 100

#

interface GigabitEthernet0/0/3

#

interface GigabitEthernet0/0/4

#

interface GigabitEthernet0/0/5

#

interface GigabitEthernet0/0/6

#

interface GigabitEthernet0/0/7

#

interface GigabitEthernet0/0/8

#

interface GigabitEthernet0/0/9

#

interface GigabitEthernet0/0/10

#

interface GigabitEthernet0/0/11

#

interface GigabitEthernet0/0/12

#

interface GigabitEthernet0/0/13

#

interface GigabitEthernet0/0/14

#

interface GigabitEthernet0/0/15

#

interface GigabitEthernet0/0/16

#

interface GigabitEthernet0/0/17

#

interface GigabitEthernet0/0/18

#

interface GigabitEthernet0/0/19

#

interface GigabitEthernet0/0/20

#

interface GigabitEthernet0/0/21

#

interface GigabitEthernet0/0/22

#

interface GigabitEthernet0/0/23

#

interface GigabitEthernet0/0/24

#

interface NULL0

#

user-interface con 0

user-interface vty 0 4

#

return

[s1]

[s1]

[s1]

[s1]

[s1]

[s1]dis

[s1]display int

[s1]display interface gi

[s1]display interface GigabitEthernet 0/0/1

GigabitEthernet0/0/1 current state : UP

Line protocol current state : UP

Description:

Switch Port, PVID :    1, TPID : 8100(Hex), The Maximum Frame Length is 9216

IP Sending Frames‘ Format is PKTFMT_ETHNT_2, Hardware address is 4c1f-cc9c-08f2

Last physical up time   : 2015-08-25 09:26:52 UTC-08:00

Last physical down time : 2015-08-25 09:26:33 UTC-08:00

Current system time: 2015-08-25 09:29:46-08:00

Hardware address is 4c1f-cc9c-08f2

Last 300 seconds input rate 0 bytes/sec, 0 packets/sec

Last 300 seconds output rate 0 bytes/sec, 0 packets/sec

Input: 11662 bytes, 98 packets

Output: 595 bytes, 5 packets

Input:

Unicast: 0 packets, Multicast: 98 packets

Broadcast: 0 packets

Output:

Unicast: 0 packets, Multicast: 5 packets

Broadcast: 0 packets

Input bandwidth utilization  :    0%

Output bandwidth utilization :    0%

[s1]

[s1]int

[s1]interface et

[s1]interface Eth-Trunk 1

[s1-Eth-Trunk1]q

[s1]int

[s1]interface gi

[s1]interface GigabitEthernet 0/0/1

[s1-GigabitEthernet0/0/1]et

[s1-GigabitEthernet0/0/1]eth-trunk 1

Info: This operation may take a few seconds. Please wait for a moment...done.

[s1-GigabitEthernet0/0/1]

Aug 25 2015 09:33:35-08:00 s1 %%01IFNET/4/IF_STATE(l)[3]:Interface Eth-Trunk1 has

turned into UP state.q

[s1]

Aug 25 2015 09:33:37-08:00 s1 DS/4/DATASYNC_CFGCHANGE:OID 1.3.6.1.4.1.2011.5.25.1

91.3.1 configurations have been changed. The current change number is 11, the cha

nge loop count is 0, and the maximum number of records is 4095.

[s1]int

[s1]interface gi

[s1]interface GigabitEthernet 0/0/2

[s1-GigabitEthernet0/0/2]eth

[s1-GigabitEthernet0/0/2]eth-trunk 1

Info: This operation may take a few seconds. Please wait for a moment...done.

[s1-GigabitEthernet0/0/2]q

[s1]

Aug 25 2015 09:33:57-08:00 s1 DS/4/DATASYNC_CFGCHANGE:OID 1.3.6.1.4.1.2011.5.25.1

91.3.1 configurations have been changed. The current change number is 12, the cha

nge loop count is 0, and the maximum number of records is 4095.

[s1]dis

[s1]display eth

[s1]display eth-trunk 1

Eth-Trunk1‘s state information is:

WorkingMode: NORMAL         Hash arithmetic: According to SIP-XOR-DIP

Least Active-linknumber: 1  Max Bandwidth-affected-linknumber: 8

Operate status: up          Number Of Up Port In Trunk: 2

--------------------------------------------------------------------------------

PortName                      Status      Weight

GigabitEthernet0/0/1          Up          1

GigabitEthernet0/0/2          Up          1

时间： 2024-10-08 10:07:11

以太网链路聚合配置1（手动模式的链路聚合）的相关文章

HCNA配置静态LACP模式链路聚合

1.静态LACP模式 静态LACP模式是一种利用LACP协议进行聚合参数协商.确定活动接口和非活动接口的链路聚合方式.该模式下,需手工创建Eth-Trunk,手工加入Eth-Trunk成员接口,由LACP协议协商确定活动接口和非活动接口. 静态LACP模式也称为M∶N模式.这种方式同时可以实现链路负载分担和链路冗余备份的双重功能.在链路聚合组中M条链路处于活动状态,这些链路负责转发数据并进行负载分担,另外N条链路处于非活动状态作为备份链路,不转发数据.当M条链路中有链路出现故障时,系统会从N条备

Eth-Trunk链路聚合配置

Eth-Trunk概述 Eth-Trunk接口能够实现负载分担.增加带宽和提高可靠性 Eth-Trunk接口把多个物理接口捆绑成一个逻辑接口 Eth-Trunk接口的链路聚合模式 链路聚合模式 应用场景 手工负载分担模式Eth-Trunk接口 当Eth-Trunk链路两端设备中有一台设备不支持LACP协议时,可在NE20E设备上创建手工负载分担模式的Eth-Trunk,并加入多个成员接口增加设备间的带宽及可靠性. 静态LACP (Link Aggregation Control Protocol

七厂节目接入，中兴交换机链路聚合配置

需求:从数字电视机房核心交换机引出复用器IP组播信号,将前端节目信号传输至七厂交换机中兴5950,因带宽不够用,需做链路聚合,并通过NSG重新调制输出.中兴5950交换机配置如下: Building configuration... ! ! vlan list 1-3 ! interface vlan 1                     // 创建vlan1,将其加入smartgroup1 ip address 172.30.101.251 255.255.255.0 out_index

链路聚合配置

二层链路聚合配置 一.手工负载分担模式配置 (1) LSW1: <Huawei>sys Enter system view, return user view with Ctrl+Z. [Huawei]sysn LSW1 [LSW1]int eth-trunk 1   //创建编号为1的eth-trunk端口 [LSW1-Eth-Trunk1]mode ? lacp-static  Static working mode manual       Manual working mode 注意:

防火墙高级应用 聚合链路 ipv6配置

Top NSD ENGINEER DAY04 案例1:配置IPv6地址 案例2:配置聚合连接 1 案例1:配置IPv6地址 1.1 问题 本例要求为两个虚拟机 server0.desktop0的接口 eth0 配置下列 IPv6 地址: server0 上的地址应该是 2003:ac18::305/64 desktop0 上的地址应该是 2003:ac18::306/64 两个系统必须能与网络 2003:ac18/64 内的系统通信 地址必须在重启后依旧生效 两个系统必须保持当前的IPv4地址并

Trunk链路的配置实验、以太网通道的作用及实验（全程操作，可跟做！）

本次我们进行的是Trunk链路的配置实验及以太网通道实验 实验环境:软件准备我之前文章里提到的GNS3.CRT和Wireshark首先我们进入GNS3界面,点击左侧的路由器图标,拖取两台路由器到拓扑操作区,再点击PC图标,选择VPC拖取四台PC机到拓扑操作区:同时对两台路由器进行配置设置(改图标为交换机.更改设备名为sw1/2.添加二层业务单板.设置磁盘空间为128Mb)接下来是连线的方式如下:1.PC1到SW1的F1/02.PC2到SW1的F1/13.SW1的F1/2到SW2的F1/24.PC

飞塔防火墙配置2条网络链路分流

飞塔配置2条网络链路分流 背景描述: 办公室网络原专线带宽不够,需要新增一条ppoe光纤拨号,实现网络提速,改善网络体验. 链路分配: PPOE光纤:非公司内网业务流量出口,即访问百度这些网站流量出口 专线:访问公司内部系统定向流量出口,即访问公司业务后台 操作步骤: 1.配置wan1为PPOE光纤拨号接口 2.更改原策略 将目的端口由原来的wan2改为wan1 3.更改静态路由 (1)更改总出口路由,由原来的wan2口更改为wan1口 (2)由于要完成wan2到公司内网通过VPN隧道的访问,所

OSPF的高级应用之地址汇总与虚链路的配置

在大型网络中,要使路由器发挥最好的性能,需要做一些优化.而由于一些原因,造成了OSPF区域骨干区域没有和非骨干区域相连.骨干区域不连续等问题.如要更改区域所有路由器配置,工作量较大,这时可使用虚链路连接没有连接在一起的区域,还有助于提供逻辑冗余. OSPF路由协议地址汇总 前面已经介绍了IP子网划分的原理,而IP地址汇总就是将多个网段汇总成一个网段,和子网划分相反.如何将多个地址汇总成一个地址呢? 具体步骤如下: (1)确定需要汇总网段的地址 (2)将各网段的地址以二进制形式写出 (3)比较各网

OSPF动态路由协议（实验篇）OSPF协议的基本配置与虚链路的配置

前言: 理论知识我在上一篇博客已经写过了,但光是掌握理论,而不去实践就如同纸上谈兵.只有理论与实践相结合,我们下能更深的理解与记忆.闲话少叙,接下来我会直接演示OSPF协议的具体配置过程.本次实验主要分为两个部分:一.基本配置:二.虚链路的配置. 一.OSPF协议基本配置: 1.实验环境 本次实验是在GNS3-1.3.10版本中进行的,具体拓扑图如下: 需要注意的是R1与R3的接口不够,需要分别添加一个NM-1FE-TX单板. 2.R1的配置 (1)给R1各个接口配上IP地址,并检查是否设置成功

OSPF虚链路的配置

什么是虚链路?虚连接是指在两台ABR之间,穿过一个非骨干区域(转换区域--Transit Area),建立的一条逻辑上的连接通道,可以理解为两台ABR之间存在一个点对点的连接."逻辑通道"是指两台ABR之间的多台运行OSPF的路由器只是起到一个转发报文的作用(由于协议报文的目的地址不是这些路由器,所以这些报文对于它们是透明的,只是当作普通的IP报文来转发),两台ABR之间直接传递路由信息.这里的路由信息是指由ABR生成的type3的LSA,区域内的路由器同步方式没有因此改变.虚连接(V