"Installation failed !" in GUI but not in CLI (/usr/bin/winusb: line 78: 18265 Terminated )
Installation failed !
Exit code: 256
Log:
**blank**
-----
Install log(when running winusbgui as root)
Installation failed !
Exit code: 256
Log:
Formatting device...
Wait 3 seconds for block device nodes to populate...
mkfs.fat: warning - lowercase labels might not work properly with DOS or Windows
mkfs.fat 3.0.28 (2015-05-16)
Mounting...
mount: /dev/loop0 is write-protected, mounting read-only
Copying...
Installing grub...
Installing for i386-pc platform.
Installation finished. No error reported.
Installing grub.cfg...
Exiting...
Syncing...
/usr/local/bin/winusb: 行 78: 20260 終止 while true; do
sleep 0.05; echo ‘pulse‘;
done
Cleaning...
/usr/local/bin/winusb: 行 78: 20593 終止 while true; do
sleep 0.05; echo ‘pulse‘;
done
Unmounting and removing ‘/media/winusb_iso_1455346491_15903‘...
Unmounting and removing ‘/media/winusb_target_1455346491_15903‘...
P.S. "終止" in the output approximately means "terminated".
______________________________________________
Installation failed !
Exit code: 256
Log:
Formatting device...
Wait 3 seconds for block device nodes to populate...
mkfs.fat: warning - lowercase labels might not work properly with DOS or Windows
mkfs.fat 3.0.28 (2015-05-16)
Mounting...
Copying...
Installing grub...
Installing for i386-pc platform.
grub-install: warning: Attempting to install GRUB to a disk with multiple partition labels. This is not supported yet..
grub-install: warning: 无法嵌入。在此次安装中 GRUB 只能通过使用块列表安装。但是块列表是不可信赖的，不推荐使用。.
Installation finished. No error reported.
Installing grub.cfg...
Exiting...
Syncing...
/usr/bin/winusb: 行 78: 7273 已终止 while true; do
sleep 0.05; echo ‘pulse‘;
done
Cleaning...
/usr/bin/winusb: 行 78: 12165 已终止 while true; do
sleep 0.05; echo ‘pulse‘;
done
Unmounting and removing ‘/media/winusb_iso_1482765713_2306‘...
Unmounting and removing ‘/media/winusb_target_1482765713_2306‘...
==================================
Do you have gksudo command installed on your system?
==================================
This issue is also reproduced in the following article:
====================================
I got same problem but solved now by
"sudo apt-get install gksu"
"gksudo winusbgui"
(i.e..type it without quotes)
Lin-Buo-Ren
referenced
this issue
on 8 Nov
Closed
Installation failure error (GUI version)
#76
Lin-Buo-Ren
changed the title from "Installation failed !" in GUI but not in CLI to "Installation failed !" in GUI but not in CLI (/usr/bin/winusb: line 78: 18265 Terminated )
======================================================
Hi again, please use the latest revision in GitHub repo and see if it‘s still reproducible(it should be, as we never fixed the problem anyway).
=======================================================
I was encountered this issue right now, with windows 10.
I‘m on ubuntu 16.04 and WinUSB 1.0.11
I tried to run the installation anyway and it worked(I just ignored the error).
=====================================================
Hi, please use the latest revision in the repository (instead of latest released version) for reproducing the issue. We‘ve have changed a quite amount of code since 1.0.11
======================================================
I got similar problem and solve it!
I dont now why, but if you use GUI its not work. Use command line in way:
sudo winusb --format /path-to-ISO-file/filename.iso /dev/sdb (or other way to your flash)
=========================================================
The issue title already tell that CLI(command line interface) works.
This issue is about the GUI problem