cisco ap 1200 升级IOS或恢复

cisco ap 1200 升级IOS

首先打开cisco tftp工具,然后连接console线,重启进入 :模式,

ap: ?
看是否支持set命令,一般都支持然后如下配置,和router 上类似
配置ip 地址
ap: set IP_ADDR 1.1.1.1     (配置ap本地地址)
ap: set NETMASK 255.255.255.0
ap: set DEFAULT_ROUTER 1.1.1.2 (tftp address)
ap: tftp_init
ap: BOOT=tftp://1.1.1.2/c1200-k9w7-mx.123-2.JA
这时候你可以看看set 的情况
ap:set
BOOT=tftp://1.1.1.2/c1200-k9w7-mx.123-2.JA
DEFAULT_ROUTER=1.1.1.2
ENABLE_BREAK=yes
IOS_STATIC_IP_ADDR=1.1.1.1
IOS_STATIC_NETMASK=255.255.255.0  
IP_ADDR=1.1.1.1
MANUAL_BOOT=no
NETMASK=255.255.255.0
然后手动的boot
ap:boot
Loading "tftp://43.82.33.2/c1200-k9w7-mx.123-2.JA"...#########################################################################################################################################################################################################################################################################################################################################################################

File "tftp://43.82.33.2/c1200-k9w7-mx.123-2.JA"uncompressed and installed, entry point: 0x3000
executing...

Restricted RightsLegend

Use, duplication, or disclosure by the Government is
subject to restrictions as set forth in subparagraph
(c) of the Commercial Computer Software - Restricted
Rights clause at FAR sec. 52.227-19 and subparagraph
(c) (1) (ii) of the Rights in Technical Data and Computer
Software clause at DFARS sec. 252.227-7013.

cisco Systems, Inc.
          170 West Tasman Drive
          San Jose, California 95134-1706

Cisco Internetwork Operating System Software
IOS (tm) C1200 Software (C1200-K9W7-M), Version 12.3(2)JA, RELEASE SOFTWARE(fc2)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2004 by cisco Systems, Inc.
Compiled Mon 08-Nov-04 12:47 by ccai
Image text-base: 0x00003000, data-base: 0x0064854C

Initializing flashfs...

flashfs[1]: 138 files, 7 directories
flashfs[1]: 0 orphaned files, 0 orphaned directories
flashfs[1]: Total bytes: 7741440
flashfs[1]: Bytes used: 1149440
flashfs[1]: Bytes available: 6592000
flashfs[1]: flashfs fsck took 2 seconds.
flashfs[1]: Initialization complete....done Initializing flashfs.

This product contains cryptographic features and is subject to United
States and local country laws governing import, export, transfer and
use. Delivery of Cisco cryptographic products does not imply
third-party authority to import, export, distribute or use encryption.
Importers, exporters, distributors and users are responsible for
compliance with U.S. and local country laws. By using this product you
agree to comply with applicable laws and regulations. If you are unable
to comply with U.S. and local laws, return this product immediately.

A summary of U.S. laws governing Cisco cryptographic products may be found at:
http://www.cisco.com/wwl/export/crypto/tool/stqrg.html

If you require further assistance please contact us by sending email to
[email protected].

cisco AIR-AP1220-IOS-UPGRD (PowerPC405GP) processor with 14326K/2048K bytes ofmemory.
Processor board ID VDF0652Q0WL
PowerPC405GP CPU at 196Mhz, revision number 0x00C4
Last reset from power-on
Bridging software.
1 FastEthernet/IEEE 802.3 interface(s)
1 802.11 Radio(s)

32K bytes of flash-simulated non-volatile configuration memory.
Base ethernet MAC Address: 00:0B:BE:B0:03:B7
Part Number                         : 0-0000-00
PCA Assembly Number               : 000-00000-00
PCA Revision Number               :
PCB Serial Number                   : VDF0652Q0WL
Top Assembly Part Number          : 000-00000-00
Top Assembly Serial Number           :
Top Revision Number               :
Product/Model Number                : AIR-AP1220-IOS-UPGRD

Press RETURN to get started!

*Mar   1 00:00:05.828: %LINK-3-UPDOWN: Interface FastEthernet0,changed state to up
*Mar   1 00:00:06.829: %LINEPROTO-5-UPDOWN: Line protocol onInterface FastEthernet0, changed state to down
*Mar   1 00:00:14.749: %LINEPROTO-5-UPDOWN: Line protocol onInterface FastEthernet0, changed state to up
*Mar   1 00:00:24.967: %SYS-5-RESTART: System restarted --
Cisco Internetwork Operating System Software
IOS (tm) C1200 Software (C1200-K9W7-M), Version 12.3(2)JA, RELEASE SOFTWARE(fc2)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2004 by cisco Systems, Inc.
Compiled Mon 08-Nov-04 12:47 by ccai
*Mar   1 00:00:24.967: %SNMP-5-COLDSTART: SNMP agent on host ap isundergoing a cold start
*Mar   1 00:00:25.007: %DOT11-6-FREQ_SCAN: Interface Dot11Radio0,Scanning frequencies
*Mar   1 00:00:25.928: %LINEPROTO-5-UPDOWN: Line protocol onInterface BVI1, changed state to up
*Mar   1 00:00:25.980: %LINEPROTO-5-UPDOWN: Line protocol onInterface Dot11Radio0, changed state to down
*Mar   1 00:00:26.988: %DOT11-6-FREQ_SCAN: Interface Dot11Radio0,Scanning frequencies
*Mar   1 00:00:27.011: %DOT11-6-FREQ_SCAN: Interface Dot11Radio0,Scanning frequencies
*Mar   1 00:00:48.294: %DOT11-6-FREQ_INUSE: Interface Dot11Radio0,frequencies in use: 2412 2437 2452
*Mar   1 00:00:48.294: %DOT11-6-FREQ_USED: Interface Dot11Radio0,frequency 2422 selected
*Mar   1 00:00:48.298: %LINK-3-UPDOWN: Interface Dot11Radio0, changedstate to up
*Mar   1 00:00:49.299: %LINEPROTO-5-UPDOWN: Line protocol onInterface Dot11Radio0, changed state to up
ap>en
Password:
ap#。。
以后可以在 记事本上编辑这样的命令 就可以了
ap#
ap#conf t
Enter configuration commands, one per line.   End with CNTL/Z.
ap(config)#
ap(config)#boot sy
ap(config)#boot systemtftp://43.82.33.2/c1200-k9w7-mx.123-2.JAap(config)#do wr
ap#reload
Proceed with reload? [confirm]
Radio system: delayed or multiple reload request, ignored
Radio system is preparing for reload...
Radio system is ready for reload.
*Mar   1 00:01:43.081: %SYS-5-RELOAD: Reload requested by console.Reload Reason: Reload command.Xmodem file system is available.
flashfs[0]: 139 files, 7 directories
flashfs[0]: 0 orphaned files, 0 orphaned directories
flashfs[0]: Total bytes: 7741440
flashfs[0]: Bytes used: 1150976
flashfs[0]: Bytes available: 6590464
flashfs[0]: flashfs fsck took 9 seconds.
Reading cookie from flash parameter block...done.
Base ethernet MAC Address: 00:0b:be:b0:03:b7
Initializing ethernet port 0...
Reset ethernet port 0...
Reset done!
ethernet link up, 100 mbs, full-duplex
Ethernet port 0 initialized: link is up
Loading "tftp://43.82.33.2/c1200-k9w7-mx.123-2.JA"...#########################################################################################################################################################################################################################################################################################################################################################################Sample Text

时间: 2024-12-23 17:36:06

cisco ap 1200 升级IOS或恢复的相关文章

Cisco asa 5510升级IOS和ASDM

asa asa(config)# dir //显示文件目录 copy disk0:/asa707-k8.bin tftp://192.168.1.149/ asa707-k8.bin //将原有IOS文件备份到TFTP服务器上 copy disk0:/asdm507.bin tftp://192.168.1.149/asdm507.bin //将原有asdm文件备份到TFTP服务器上 copy tftp://192.168.1.149/asa803-k8.bin disk0:/asa803-k8

Cisco AP IOS升级

Cisco AP IOS升级: 方法一, 此方法也可以用于瘦AP到胖AP的升级, 可以是胖AP IOS 系统本身的版本升级: 前提准备: Console线和网线接AP和笔记本,设置笔记本IP 10.0.0.2/8,打开TFTP设置  AP's IOS路径(.default文件) 然后按住Mode键, 直到提示释放按键再释放Mode键,这时候AP会自动去查找TFTP的IOS路径然后升级或者替换当前的IOS. 方法二,此方法用于胖AP IOS 系统版本的升级: ap# archive downloa

Cisco交换机升级IOS

Cisco交换机的IOS升级,其实挺简单的,但是需要注意的是,不能让交换机flash存储为空,一定要有一个IOS在,否则没有IOS在flash里面,等着用xmodem上传IOS吧,那样你的时间可以是废了很多啊.因为对于Cisco Catalyst 2950.2960.3550交换机丢失IOS或IOS故障时,是无法使用rommon模式的,因为压根儿就没有,只有Cisco Catalyst 4006.4506才有rommon模式,本篇文章以Cisco Catalyst 2950为例. 1.首先下载T

Cisco路由器升级IOS

今天把公司里的一台老式Cisco路由器拿出来看了看,还能用,就是IOS的版本有点儿低,而且之前同事装的IOS版本还无法把路由器的所有接口都认出来,于是乎动手重新安装了IOS,我的路由器是2600,新的IOS版本为:c2600-i-mz.123-26,这个IOS是我从网上找的.一般124的都是企业级的路由器,我的这台不是,凑合用吧. 1.首先上网下载一个Cisco TFTP Server,下载回来后解压缩,运行"TFTPServer.exe",运行了这个程序也就代表着你的这台计算机就是一

Cisco PIX防火墙灌IOS

事件背景: 上周二出差,拿着在公司测试好的防火墙在客户机架上加点居然水土不服启动不起来,不断重启截图如下: 试过各种方法均FALSE,在百度上寻找解决办法,居然有人让送修.万般无奈之下决定重新灌一个新版本的IOS,死马当活马医.实在不行就让同事发个顺丰航空件,把公司另一台PIX墙发过来.结果灌完IOS之后,居然启动开了.实在想不出是什么原因导致以上无法启动的这个问题,在分享出灌IOS的步骤之前,如有哪位神级高手知道什么原因及解决方法,在下愿屈身请教. Cisco PIX防火墙灌IOS步骤: 首先

CCNA学习笔记3---备份和升级IOS

1,备份配置到TFTP 2,从TFTP COPY 到 run 3, 备份IOS 4,升级IOS 5,如果升级失败的解决办法 ◆ 一.备份还原配置 1,保证路由器和电脑(tftp服务器)网络IP可达(直连,同网段) 2,电脑运行tftp软件 3,路由器上设置hostname test1用于验证时看出区别 copy running-config tftp: 4,电脑打开tftp保存路径找到hostname test1名字的文件 5,路由器修改hostname 为test2 6,从tftp服务器上co

CiscoASA防火墙升级IOS版本需注意的问题

引用Cisco官方的公告: 在Internet密钥交换(IKE)1版本的漏洞(V1)和IKE协议版本2(v2)Cisco ASA软件代码可能允许未经身份验证的远程攻击者造成的影响重装系统或远程执行代码. 该漏洞是由于受影响的代码区缓冲区溢出.攻击者可以通过发送特制的UDP数据包来利用此漏洞影响的系统.一个漏洞可能允许攻击者执行任意代码,获得系统的完全控制或导致重装系统的影响. 注意:只有流量定向到受影响的系统可以用来利用此漏洞.这个漏洞影响配置防火墙模式只在单个或多个上下文模式系统.此漏洞可以被

Cisco的互联网络操作系统IOS和安全设备管理器SDM__路由器软、硬件知识

路由器软.硬件知识 1.路由器的组件: 组件 解释 Bootstrap 存储在ROM中的微代码,bootstrap用于在初始化阶段启动路由器.它将启动路由器然后装入IOS POST(开机自检) 存储在ROM中的微代码,POST用于检测路由器硬件的基本功能并确定哪些接口当前可用 ROM监控程序 存储在ROM中的微代码,ROM监控程序用于手动测试和故障诊断 微型IOS Cisco调 用 RXBOOT或 bootloader(引导装入程序),微型IOS是一个在ROM中可以启动接口并将Cisco IOS

ASA Failover业务不中断升级IOS

之前给客户割接,客户额外要求升级两台ASA5520防火墙的IOS.IOS版本842要升级到847. 当然客户什么都不懂,需要和大家说明的是,ASA升级IOS注意点,严重注意: 检查防火墙的内存--5520跑8.3以上版本内存要2G,其他型号内存需要都不一样 是否做了Failover--做了HA后升级IOS要保证不中断业务 明确升级到的版本是多少--有升级顺序讲究,842先升级到845或846再升级到847,其他IOS升级顺序也不一样 知道这些注意点,接下来就开始升级IOS. 1.先在Active