wlcore: firmware chunk too long

insmod wlcore_sdio.ko 的时候出现的错误

43.767890] Powering on wl12xx

[ 143.846003] Powering off wl12xx

[ 143.849249] Powering on wl12xx

[ 143.949008] wlcore: ERROR could not get configuration binary ti-connectivity/wl18xx-conf.bin: -2

[ 143.960629] wlcore: WARNING falling back to default config

[ 143.967443] add wake up source irq 108

[ 144.292965] Powering off wl12xx

[ 144.319907] wlcore: loaded

[ 144.325471] wlcore: driver version:

[ 144.332153] wlcore: timestamp: Mon May 25 19:56:12 2015

[ 228.991855] Powering on wl12xx

[ 229.329532] wlcore: firmware chunk too long: 1731433

[ 229.334802] Powering off wl12xx

[ 229.361806] Powering on wl12xx

[ 229.653852] wlcore: firmware chunk too long: 1731433

[ 229.659057] Powering off wl12xx

[ 229.691803] Powering on wl12xx

[ 229.983832] wlcore: firmware chunk too long: 1731433

[ 229.989046] Powering off wl12xx

[ 229.992057] wlcore: ERROR firmware boot failed despite 3 retries

[ 250.011866] Powering on wl12xx

[ 250.305219] wlcore: firmware chunk too long: 1731433

[ 250.310490] Powering off wl12xx

[ 250.341847] Powering on wl12xx

[ 250.635159] wlcore: firmware chunk too long: 1731433

[ 250.640424] Powering off wl12xx

[ 250.671848] Powering on wl12xx

[ 250.963833] wlcore: firmware chunk too long: 1731433

[ 250.969041] Powering off wl12xx

[ 250.972052] wlcore: ERROR firmware boot failed despite 3 retries

看了一下，原来都不会出现固件太大uc问题，估计是拷贝固件的时候固件的数据出错导致

的

后面对比了一下固件。发现真的是不一样了。所以重新拷贝了下就可以了。

时间： 2024-08-01 07:57:05

wlcore: firmware chunk too long的相关文章

TI WL1271 WiFi Linux 設定

1. /etc/wpa_supplicant.config 內容 ctrl_interface=/var/run/wpa_supplicant network={ ssid="ssid_namef" psk="password" key_mgmt=WPA-PSK } 2. commands wpa_supplicant -iwlan0 -c /etc/wpa_supplicant.conf& sleep 1 ifconfig wlan0 down <

mongodb chunk 大小设置

默认是64MB,取值范围是1 MB 到 1024 MB. 那修改会造成什么?下表简单总结: chunk size 调节 splitting次数(碎片数) 数据跨shard数目数据均匀网络传输次数 migration次数单次migration 传输量查询速度变大减少变少不太均匀变少变少变大变快变小增多变多更均匀变多变多变小变慢在数据量很大的情况下,考虑网络带宽,如果发现带宽占满,可以考虑调小chunk size,这样migration造成的传输量会降低在

[MODx] 8. Snippet get data, chunk display

Simple Example: Lets process this chunk and output its value. We have this Chunk, called "WelcomeChunk": <p>Welcome [[+name]]!</p> We'll put this in our Snippet: $output = $modx->getChunk('WelcomeChunk',array( 'name' => 'John',

[mysqldumpslow 报错] Died at /usr/local/mysql/bin/mysqldumpslow line 161, <> chunk 236.

mysqldumpslow报错:Died at /usr/local/mysql/bin/mysqldumpslow line 161, <> chunk 236. 总结:是因为top数目太多了,mysqldumpslow遍历不过来的缘故. /usr/local/mysql/bin/mysqldumpslow -s -t 15 /root/db01-102-slow.log 1,把r去掉试试,还是报错,参数不识别. [[email protected] ]# /usr/local/mysql/

Lucene4.2源码解析之fdt和fdx文件的读写——fdx文件存储一个个的Block，每个Block管理着一批Chunk，通过docID读取到document需要完成Segment、Block、Chunk、document四级查询，引入了LZ4算法对fdt的chunk docs进行了实时压缩/解压

前言通常在搜索打分完毕后,IndexSearcher会返回一个docID序列,但是仅仅有docID我们是无法看到存储在索引中的document,这时候就需要通过docID来得到完整Document信息,这个过程就需要对fdx/fdt文件进行读操作.为了更清楚地了解fdx/fdt文件的作用,本文把fdx/fdt文件的读和写整合到了一起,尽管这在Lucene中是两个分开的过程. 1. 索引生成阶段索引生成阶段包含着一个复杂的过程,所以了解本文前最好对Lucene的索引架构有一定的了解,可以参考博

wlcore: firmware chunk too long

wlcore: firmware chunk too long的相关文章

TI WL1271 WiFi Linux 設定

mongodb chunk 大小设置

[MODx] 8. Snippet get data, chunk display

[mysqldumpslow 报错] Died at /usr/local/mysql/bin/mysqldumpslow line 161, <> chunk 236.

Lucene4.2源码解析之fdt和fdx文件的读写——fdx文件存储一个个的Block，每个Block管理着一批Chunk，通过docID读取到document需要完成Segment、Block、Chunk、document四级查询，引入了LZ4算法对fdt的chunk docs进行了实时压缩/解压

firmware 固件

cxf client在后台不通且chunk设置为false的时候不能在控制台输出请求日志

在ESXi上如何查网卡的driver的版本号和firmware的版本号？

Error: Chunk.entry was removed. Use hasRuntime()错误解决