How to calibrate steering angle sensor with BMW V1.4.0 OBD II scanner

Here is the detail instruction on recode or re-calibrate BMW E46 steering angle sensor with BMW V1.4.0 PA-Soft diagnostic scan tool.

Equipment:
BMW V1.4.0 OBD II scanner
A laptop running Windows XP or Windows 7 home

NOTE:
Vehicle VIN is required during the procedure.

1) Install BMW V1.4.0 PA-soft software, you may find some clues in this thread
http://www.bimmerforums.com/forum/showthread.php?2109285-HELP!-how-to-install-the-proper-driver-for-PA-Soft-BMW-scanner-1-4-0
2) Connect BMW V1.4.0 diagnostic interface with vehicle via OBD port
3) Come to main function menu and find out "LEW" option to open the LEW program
4) Select "Reprogramming"
5) Click "Write ADFG" on the Reprogramming menu
6) Enter "00XXXX" (the last 4 digits of your vehicle VIN), press "OK"
7) When complete communication, click "Read EEPROM"
8) Edit the values ??highlighted in the picture below

9) Use a hex to anis converter for 2 letters
Check the values ??highlighted red color in the image "20 45 31 4A 4C"
These values ??can be translated into the last 7 digits of your vehicle VIN:

4C in hex converts to the letter L
4A in hex converts to the letter J
31, 45, 20 are the last 7 digits of the VIN LJ31452
Change for your VIN

10) Click "Save" button to save settings
11) Click "Write EEPROM"
12) Erase all error codes in LEW and ABS program after complete precious procedures.
13) Back to main function menu or exit the PA-SOFT software program.

You can get good quality BMW PA-SOFT OBD scan tool with cheap price, like this one cheap $ 23 in aobd2shop.

时间: 2024-10-09 10:18:32

How to calibrate steering angle sensor with BMW V1.4.0 OBD II scanner的相关文章

How to program Coverlet ECBM with GM Tech 2 diagnostic scan tool

If ESC (Electronic Stability Control) DTC C0460, C0280 or C0196 etc displays on Driver Information Center (DIC) or you get the ECBM module replaced, you need to perform steering angel sensor calibration. In this case, you need to1) Use SPS (Service P

FAQ of Launch X431 Creader VIII (CRP129)

Launch X431 Creader VIII(CRP129) is a comprehensive diagnostic instrument. With Multi-language to choose. It is can reset brake block,corect steering angle sensor, engine oil light reset and so on. Creader VIII can replace CRP129 definitely in functi

Autel MaxiIM IM608 VS MaxiIM IM508 VS Auro OtoSys IM600 VS IM100

Autel factory combine uobdii.com engineer make a comparison table about Autel MaxiIM IM608 VSAutel MaxiIM IM508 VS Auro OtoSys IM600 VS Auro OtoSys IM100. They can compare with each other in the aspects of IMMO (key programming, key learning, pin cod

Autel MaxiIM IM608 VS Autel MaxiSYS MS908S PRO

Autel MaxiIM IM608, replacement of Auro OtoSys IM600, features in IMMO functions for over 60 worldwide makes and models as well as service reset functions (EPB, DPF, SAS, Oil Reset, BMS and TPMS Sensor ID Re-Programming etc). Autel Maxisys MS908S PRO

Creader VIII VS. Creader VII+

Launch x431 diagun is professional universal auto diagnostic tool which designed and developed by LAUNCH aimed to do vehicle diagnostics for both repair technicians and DIYer. While among them, Launch X431 Creader VIII (named CRP129) and Creader VII+

hoj 1010 The Angle

The interval angle between the hour hand and the minute hand is always among 0 degree and 180 degree(including 0 and 180 degree). For example, when it's 12 o'clock, the angle of the two hands is 0 while 6:00 is 180 degree. Try to calculate any degree

BMW INPA / EDIABAS full iso torrent Free download

BMW engineering and development diagnostic software can project powerful functions for both old and new BMW series, like E39, E60, E65 etc, CANBUS modelE60, E65 and old vehicle models, like E39. Following are some of the most significant functions of

How to setup BMW INPA Ediabas software

You can download BMW INPA 5.0.2 (last version, includes NCSExpert and WinKFP) software here: http://down.eobd2.fr/bmw-inpa-502.zip (this set is fully tested by me). Unpack INPA and run Programminstallation/setup.exe 1. Choose language: 2. Select "I a

How to install BMW ENET E-sys F-series coding software step-by-step

Equipment:BMW ENET (Ethernet to OBD) InterfaceE-sys ICOM coding software with soft EST tokens and Pinpsdzdata 54.2A laptop running Win XP O / SBackup necessary CAF file Install E-sys softwareInstall E-sys EST tokensInstall psdzdata 54.2Connect and co